商店页面
Stormworks: Build and Rescue
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Stormworks: Build and Rescue

商店页面
Stormworks: Build and Rescue >  创意工坊 > Phil 的创意工坊
38 个评价
Smooth RPS Limiter (Modular Engines and Prefabs)
描述 讨论0 留言31 改动说明
   
奖励
收藏
已收藏
取消收藏
Vehicles: Air, Sea, Land, Mechanical
Microcontrollers: Calculation, Fluid, Modular, Microcontroller
标签： v1.2.3
文件大小
发表于
更新日期
164.550 KB
2021 年 6 月 13 日 下午 1:00
2021 年 6 月 13 日 下午 1:21
2 项改动说明 （ 查看 ）
创建者
Phil
离线
查看所有 57 个合集（也许有些被隐藏了）
3,373 不重复访客数
1,546 当前订阅者
38 当前收藏人数

订阅以下载
Smooth RPS Limiter (Modular Engines and Prefabs)

描述
If you are unhappy with the 0.5 method consisting in cutting the throttle in half if the RPS are above the set limit, try out this Microcontroller! (No PID inside!)
With this smooth approach you can get a more continuous engine throttle resulting in less fuel consumption and heat generation as well as less unpleasant engine noise.

You can enable variable RPS limit to change that limit in-game while on the move.
A hardness factor is determined by your set RPS limit to keep the resulting RPS from overshooting more than 1. You can manually increase that factor if you want to be closer to the RPS limit.

This controller works on no load engines too but is meant for engines under load like vehicle engines.
31 条留言
< >
warppioneer 2024 年 12 月 14 日 上午 10:16 
Might sound stupid, but if the engine speeds up and slows down a lot, what should I do? I changed the manual hardness factor around, it only made it worse. I know I should change the automatic hardness determination factor, just not sure what to change it to.
Phil  [作者] 2024 年 7 月 3 日 上午 7:12 
Throttle is throttle, you need to add fuel manifold throttle which without supercharge can just be half of the air throttle.
CatLover2500 2024 年 7 月 2 日 下午 1:34 
Does it work with modular engines?
MRX 2024 年 3 月 31 日 上午 6:20 
you should add idle rps
Firegecko 2023 年 12 月 14 日 上午 12:16 
Awesome. Just what i was needing. Thanks heaps!
Decadenced 2023 年 8 月 6 日 上午 10:25 
works fine 4 me, thank u
Phil  [作者] 2023 年 6 月 28 日 上午 9:56 
No it doesn't, just an RPS limiter like the name says, not an ECU. To idle engine you could just switchbox to a PID with P of 0.3.
buder28 2023 年 6 月 27 日 下午 2:16 
that mcu dosent have any kind of idling controll last time i tested
you will need to figure that out
Ninovium 2023 年 6 月 27 日 下午 1:39 
btw if you connect an actual throttle to the controller, then the engine just goes to 1 rps and dies. If you connect to W/S, it revs the engine to the max until it explodes. (it also implodes your ear drums)
Ninovium 2023 年 6 月 27 日 下午 1:37 
I have the same problem as the guy below, could you show us how to actually connect it? (to help idiots like myself)