Space Engineers

Space Engineers

26 个评价
HVK Titan I Armored Recovery Vehicle
   
奖励
收藏
已收藏
取消收藏
Type: Blueprint
文件大小
发表于
更新日期
1.021 MB
2018 年 2 月 27 日 上午 8:40
2018 年 2 月 27 日 上午 10:41
2 项改动说明 ( 查看 )

订阅以下载
HVK Titan I Armored Recovery Vehicle

在 hav0kk 的 1 个合集中
HAV0K Industries Military Branch
19 件物品
描述
[100% Vanilla, Mouse Controlled, Skid Steering]

Description
This is the Titan I Armored Recovery Vehicle, used to help out damaged tanks and if needed tow them away from the fight. To fulfill it´s task the ARV is equipped with a dozerblade at the front, to stabilize the hull when lifting things or in order to clear paths. For the towing part, it features an arm with Landing Gears at the end, capable of lifting and towing equipment. There´s also a second seat for the driver of the tank in need of help. It is based on the new Vanguard II chassis, so it´s reliable and can take and can take a beating, however, it is not built to face other tanks in direct engagements.

Huge thanks to Whiplash and MMaster for their incredible scripts, which allow us to build cool stuff!
Also thanks to Inky for his Tracks!

Make sure to check out my other tank designs here!


|Tips|
-
Handle the arm with care, it hasn´t snapped in any way for me, but the chassis i wobbling around a bit when using the arm.
-
The Landing Gear at the end of the arm can rotate in a vertical axis, to enable the two connected vehicles to corner. Only unlock that last rotor when the tank is locked to the one that needs towing. Also lock it again before you let loose the tank, so that the Landing Gear is always facing the right direction. Otherwise it might turn around and face the wrong way for the next towing mission.
-
Make sure the dozerblade is lifted up and the rotor locks are enabled, when driving alot.
-
Read the controls below.

|Basic Stats|
Block count: 1101
Weight: ca. 100 tons
Top speed: 75 kph

|Features|

- Mouse-controlled gatling turret and crane arm(MART Script) by Whiplash

- Gyro-assisted Skid Steering (Skid Steering System v12[github.com]) by Whiplash

- Info-LCDs (MMaster´s Automated LCDs 2)

- Bearing LCDs for driver and codriver Planetary Bearing & Compass by Whiplash

- Dozerblade with two rotors (doubled torque)

-Warning System for unknown objects within 50m

-Connector on the rear of the chassis

-two seats and increased cargospace

|Controls|
Driver
Toolbar 1
:
1-Landing Gear Switch Lock
2-LG Autolock On/Off
3-Arm Lock On/Off
4-Arm End Rotor Lock On/Off
5-Landing Gear Rotor On/Off
6-Landing Gear Rotor Lock On/Off
7-Camera Front Upper
8-Camera Rear
9-Camera Arm

Toolbar 2:
1-Rotor Dozerblade On/Off
2-Dozerblade Reverse
3-Dozerblade Lock
4-Camera Gatling Turret
5-Camera Front Lower
6-Vicinity Warning Sensor On/Off
7-Decoy System On/Off

Toolbar 3:
1-Reactors On/Off
2-Gyroscope Assist On/Off
3-Ore Detector On/Off
4-Rear Connector Switch Lock
5-Cockpit Lighting On/Off
6-Skid Steering On/Off
7-Increase Wheel Friction

Toolbar 4:
1-Antenna On/Off
2-Beacon On/Off
3-Batteries Recharge On/Off
4-Batteries Discharge On/Off
5-Air Vents On/Off
6-Hull Marker On/Off
7-Hull Repair Projector On/Off

Codriver/ Gunner
Toolbar 1
:
1-Gatling Gun
2-Camera Gatling Turret
3-Camera Front Upper
4-Camera Rear
5-Searchlight On/Off
6-Gatling Turret Lock
9 条留言
Cray 2018 年 8 月 12 日 上午 6:15 
thanks!
hav0kk  [作者] 2018 年 8 月 12 日 上午 3:26 
After placing the rotors like that I remove the rotorheads and build the crane arm, including the heads. After that you have to manually put the crane arm in a position where the rotors and heads can be connected via the control menu (with a lifting ship) and voila. You can do that with any amount of rotors, just prebuild the arm with the heads and connect it manually. Don´t forget to set the rotor´s offset values to 0 on small grids and -40 on large grids, so they don´t push or pull against each other. About the collision, that´s just trial and error, if it´s jittering after placing try again. Hope I could help you :)
Cray 2018 年 8 月 11 日 上午 7:07 
There are a few things i need to know: how did you place two rotors to move the same grid (crane double rotor elevation) and how did you not make the rotors colide with the blocks near them? i'm always having problems with this
hav0kk  [作者] 2018 年 3 月 5 日 上午 8:31 
Thanks! Yeah, me too :)
Daedooloos 2018 年 3 月 5 日 上午 3:53 
this is great! i wish it had more popularity tho
hav0kk  [作者] 2018 年 3 月 2 日 下午 6:00 
Thanks!
INKY /ᐠ_ ꞈ _ᐟ\ 2018 年 2 月 28 日 下午 10:51 
So pretty. I like
hav0kk  [作者] 2018 年 2 月 27 日 下午 2:36 
Thx!
Deathlok-L17 2018 年 2 月 27 日 下午 2:24 
very cool