So complicated that its bad

So this is working to keep the torque rotation aka death spin from happening, but for some reason there is absolutely ZERO pitch response for me, I can roll and yaw, but forward and aft pitch is not happening, idk what im missing.

This controller for jet engine?

please add a physics sensor support

when i descend the helicopter falls down literally

when i roll to the right the helicopter yaws to the left?

@user this controller is for coaxial helis that have two rotors ontop of them, like the ka52. do your research before calling it crap and try to make it work correctly, not everything works first time

Works like a charm! Thanks a lot!

It's good, but can you use a physical sensor? It saves space

Hooked everything up as directed and it rotates counter clockwise no matter what I do, I've checked the orientation of all sensors and they are all connected into the gyro correctly. My seat axis trims and all that are set to 0. When I spool up, it rotates counter clockwise and lifts about 2 meters above the ground and then drops. Help please?

would be nice to have a description for each node (when you're hovering your mouse over them

this is likely broken

cant figure out this crap

what do i connect the engine throttle to

Along the same axis. In this case both rotor disks mounted are one after another, in a straight vertical line.

what actually is coaxial?

This is amazing. Just finished my first really ugly helicopter and it flies perfect.

Hello, i really liked your jet engine controller in here so i cut out everything else and i was wondering if i can post (ofc crediting u) and if u want i can link it here

am i able to just ignore the engine nodes if i have my own system?

DUDE this gyro made me able to balance a heli with a 5 degree MGB tilt. AND it increased my top speed from 60 kts to 90. Good stuff this thing rocks.

I got a problem with this gyro, I got everything connected as indicated, CG is dead centered 8 blocks below the coaxial rotors and it holds perfectly still when there is no wind. however as soon as the wind is over 50% it starts to drift in a weird way. if the wind comes from the rear, it will drift slowly with the wind. if the wind is coming from the front, it will fly into the wind on its own. the higher the wind the stronger the effect, near 90% wind, if I'm facing into it, I can't even get it to stop moving forwards manually, even if I put the wind into my side it still keeps going forward. only thing I can do is put the wind into my back at which point the gyro will allow me to manually stop its forward travel. but I have to fight it all the way to the ground.

Having an issue with my helicopter constantly moving to the left and back. I adjusted the pitch trip forward by 1 and now it just goes forward while still drifting to the left. It's very small and moves about a walking pace. The balance is centered on the same block inline with the props. I thought it might have to do with my controller so I unplugged and went as far as rebooting my computer since just closing and restarting the game didn't resolve it. Still didn't fix it. I don't know what else to try but I know the vanilla Gyro doesn't do this to me. It just flips out when I try using the collective. Which also flips out with your controller so I don't know what could be the root cause of this.

Forgot to say, when actually giving input other than avoiding the collective, it flies great with pitch, roll, and yaw.

100% functional, just built a new micro-heli with this and it works perfectly fine

100% broken, I dont wanna have to use my yaw to control collective. Plus it doesnt even turn no matter what I do

So hooked this up, and now with any amount of upforce, it spins in place like a top

i cant get any controls into it from my seat for some reason

My collective stays at the maximum whatever i do please help

damn it stopped working

Any possibility for a gyro like this for conventional helicopters? I Love how stable this is.

yes but the trim is only for pitch.

Use the trim settings in the MC or rebalance the aircraft

coaxial helicopter keeps tilting to the right, is there a fix?

You could go into the MC to channel it reads from or pack your look coords into another composite signal.

Is it possible to use it with Look X and Look Y outputs from the pilot seat?

any chance you could make a quadcopter adaptor for gyros?

Yes, it is possible, considering the rotors are rotating in opposite directions.

i was wondering if i can do tandem roto with this

Упомяну конечно же.
Хотя я не уверен что вертолёт доберётся до Воркшопа

Наверно никто не будет против, если я возьму это.

oki

There is no rotor braking in this controller, but you can add the car wheel to the power shaft and use its brake.

how do i set up rotor braking?

Very good

Another amazing gyro ZE!

I seem to have tweaked it to work now

Make sure two speed sensors have proper orientation and are set to the directional mode, also set all seat axis trims to 0.

this is a great gyro :D but I seem to be having a problem with the position hold, it seems to slide around a bit more compared the to game gyro

Thank you very much for the fast response! I swapped the rotors so now the clockwise one is on top and moved the altitude sensor up by one so it was even closer, and now it works! I can't understand how I could of connect the controller wrong 8 times in a row yesterday but I must of hahaha thanks again for the response and the incredible gyro!

Hi, the gyro is working fine and probably you connected something wrong. Check the angular speed sensor orientation and its plus arrow should be pointing clockwise. Or send the xml of your heli to me via discord, Uran_Wind#3382

Hello, I'm making an ultra light coaxial Heli. When I set this microcontroller up it won't stop rotating anti clockwise. My rotors are counter rotating and I've made sure to follow your directions exactly. So I think it must be that my heli is too light or it's a new problem regarding an update. Is this still working?