this ship is awesome i love the pitch roll stabilizer, i have noticed that wih crane stabilzer on u can capsize by lifteng and rotating the argo to fast

Is this laggy?

I think the ARGO needs an update with the flow rate of her Airlock. It take a long ass time to drain. Maybe it is the depth I am at (260m)?

please not mega big sub with argo

@RichyRichGold it has batteries

I can't make the winch on the crane go up or down

@RichyRichGold you have to throttle up the generators and turn on the fuel pumps then use the starter

For some reason this works without the generators on? Why would that be?

where is it

as a danish person i approve

@sjpengelly15 It is definietly able to lift the ARGO. Try to raise the Physics Quality to High: the pivots and ropes are a lot weaker at lower Physics Settings.

iv noticed when trying to the lift the argo with the crane that is built into the ship it does not seem to be able to lift the weight of that idk if its a issue on my end or in general,

is this sinkable

im surprised you found the problem that fast. well done.

you should also add a way to access the area below deck easier in case the engines or hull need to be repaired. part of the hull below the waterline along the bow got damaged when i was using it the other day, but because of how stormy the weather was it was impractical to get in the water and repair it from outside. theres just that one little ladder/access shaft for the aft near where the argo dock is, but every time i tried to use it to get below deck id get stuck.

a gps/map would be nice too so you know where you are in the world, considering the fact that its an exploration vessel.

@76561198192726397 Thanks for reporting it. It's due to a bug in the Up-Down Counter logic block behavior the devs have added in the latest update. I forgot to fix the Flares Logic on this one, will do it right away!

right when i spawn it the argo launches 2 flares

@Toasted Toast I've just tested this and it works fine, Maybe you lowered the Physics Settings? I'd suggest you set Physics Quality to Max, it should work fine then.

keeps flipping over when i deploy the argo, even with roll stabilization on

@Buzz313TH Yes, I might add a Dynamic Positioning System in the future, though right now I'm working on a new ship.
About the Anchor issue, thanks for pointing it out, usually I "fix" that by going a bit in reverse when retracting the Anchor ;)

Hey Thanks C4RBON... If your taking requests.. ;) Then here's a few, considering this is the only boat that can consistently launch and recover the larger submersables.. 1) Dynamic positioning would be amazing. It's available somewhere here in the workshop by a well known author. 2) The bow below the waterline inhibits the anchor from retracting.

@Buzz313TH Thanks! Yes, I may rework how the throttle is set up and update this.

Nice boat, but the throttle needs a deadzone badly.

@Vokun Vulon You can either stand on the submarine you want to connect to the winches, or jump up from the water and connect the ropes

How does one attach the moonpool winches? they dont have anything attached by default and seem a bit high up to reach with a rope, or do i need to be standing on the submarine?

finally i dont have to deal with the pain of loading ARGO on!

@O. Forest Thanks man, glad you liked them!

@C4RB0N Ah alright was just wondering if the ARGO that spawns with this one was the updated one. Thanks for the answer. It is an amazing ship and an amazing sub. Perfect for this update!

@O. Forest I didn't change the ARGO's connectors setup, so it's still fully compatible

@C4RB0N Oh alright. It is just because the last ARGO updates was listed on the 2nd of June where this ship's last update was 27th May.

@O. Forest It already does (if you're referring to the Argo - Moonpool Version)

Will you update this to fit updated Argo?

Thanks!
I forgot the Crane Connector! xD

@Sprock3tCrack3rs Enter the Crane Operator seat, lower the Crane Connector on top of the ARGO’s Top Connector (in the center of its roof), and then activate the Crane Connector.

how do I conect crane to ARGO!

@Croc I've just tested it and it works perfectly. You probably have reduced the Physics Quality in the Game Settings. Even on "Medium" quality it can lift the ARGO, though "High" is always recommended.

Crane does not work with argo. Tried to pull it up does not work it just stays there. Its also unattached

@sovietmusiclover Yes, it fits under the train bridges, just remember to fold the mast (there's a button close to the Helm).
You can land an heli on the deck, there's definitely enough space for that.

also can this thing fit underneath the bridges? i dont want to risk it slamming into one while doing something.

this thing is really cool. i dont know how people can make stuff as good as this. also it would be cool is it had a little heli pad somewhere just to make it have even more versatility.

@Poncho Thanks! Glad you liked it!
1. Yes, indeed you can winch the ARGO (and other small subs) up in the Moonpool: just make sure to use the 4 winches to lift it up completely before closing the Door.
2. Yes, the ARGO on the ODIN'S Deck is the same as the standalone ARGO.
If it's difficult to exit via the Top Hatch, jump in the Padded Seat next to it.

Love the Moonpool concept! Fantastic implementation - would suggest slightly more room for manouvering the ARGO and other submersibles. A couple of questions:
1. Is the intent to close the Moonpool doors after a submersible has been winched up? I cannot fit the ARGO high enough
2. Is this ARGO model on deck the same as the stand-alone? The cabin bilge pump did not activate, and is difficult to exit through the top hatch

@ant.sne.298 No, shouldn't be an issue: I have a very basic laptop and it runs perfectly fine.

Is this going to be an issue for low end computers?

@KenneGlitch Yes, the update is coming very soon, it will also have a moonpool ;)
(pic here: https://i.imgur.com/a5Hd4M4.png)

is this going to be updated with 1.0 stuff?

@goomz Thanks man! A new update with a moonpool for submarines is coming soon ;)
(pic here: https://i.imgur.com/a5Hd4M4.png )

Cool

@RJGaming Yeah, sure: as long as you give proper Credit in the Description, and link to this Page, yes ;)

@C4RBON, I am currently working on some underwater liftbags, and I was wondering if I could post on the workshop a version of the ODIN Diving Support Vessel + ARGO, with the Liftbags. Would that be fine with you? I can't seem to find the Original Goomz ODIN SV.

ya as soon as i spawn it in it lags however ive never left port with it because of the lag, but ill give it a shot