Can you make this use the physics sensor

constantly rolls to the right a little bit

yes

does this work for jet engines?

I think it would be incredibly useful if you could figure out some sort of custom gyroscope controller, since i've almost never been able to properly use the gyroscope

Better to use a separate ECU.

Does this work for Modular engines or am I better off using a seperate ECU?

what mode works with ducted fans or does that not matter if im not using the engine controller parts

Will you ever make a new one of these?

not really

is this up to date still?

I have this installed on two separate aircraft, and they both hold level pitch when the gyro is turned on. However, level pitch does not correspond to level flight. Both aircraft start a very slow descent when at level pitch. It is realistic for an aircraft to have pitch up attitude when at cruise. So, I was wondering was the solution may be or is it in my design? Is there a way for me to tell the gyro to hole a different sensor value other than 0?

mmm yes it does seem like the 2 giant control surfaces were the cause

Probably you have very large control surfaces while flying at very high speed.

my roll ailerons also wobble a ton at speed even with roll pid sensitivty at minimum

increasing pitch turn speed all the way to 5 still doesnt allow it to angle high enough

Increase the pitch turn speed.

I just added this onto a jet of mine, but at any semi-high speed it starts wobbling to all hell, reducing pid sensitvity reduced this but now the pitch angle is extremely low so i can barely even take off anymore or do turns

ok ill do that

You can just remove unused numerical nodes and unhook links from the composite node.

is there a version of this microcontroller that only offers the autopilot

Yes.

So to not use the optional engine controls, I just don't hookup the engine nodes?

You need to hook up all angular speed and altitude sensors for the flight control, although there is a compact version without autopilot and fewer required sensors.

Do I need the sensors just for the flight controls? like i dont want no autopilot or altitude hold

oh thanks it was that

Make sure you selected the correct aileron orientation in mc properties.

my thing just SPINS and keeps rolling

Thanks, updated and fixed.

thanks this help a lot. although the roll trim and roll PID sensitivity are swapped at the comp write by the roll pid lua.

is there a way to limit yaw when autopilot is on? when i use manual control its set up ok, but when i turn on autopilot it turns yaw rudder way to much and plane starts loosing altitude.

There are too many things on your plane that spoil its aerodynamics and require a workaround to achieve stable flight, like excessive thrust of fans, destabilizing front fins, small fins spam, control surfaces on subbodies, and fins on the missiles. Also Thales mod gives my pc a significant lag every time i open the inventory, and personally i dont like any oversized and overpowered vehicles. Try someone else's gyro from workshop or the default one.

Hey sorry if im bothering you and i really hate to do this but I still have a problem where my elevators increases its angle until its maxed, if you can help me i would greatly appreciate it

Alright noted, but what about the elevators constantly trying to pitch up? like it constantly try to pitch up with max elevators, sorry if im bothering you im still new to making things in SW

It is aerodynamically unstable, try to make it fly in a straight line without nose diving first.

https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?edit=true&id=2898482624 Its kinda janky and it uses Thales aviation parts for weights, and it needs infinite fuel to work

Yep, you can send me your plane

Alright i have problem, my plane's agility is great but my plane often randomly pitches up, like its not a little pitch its like max pitch, and this may be a diffirent issue but when i try to use the ALT hold it just randomly pitches down, if you want i can just send my aircraft if needed

If the airplane holds the altitude, the nose should be slightly pitched down to compensate the lifting force of the wings and other chassis blocks.

hey uran how do i tune out the nose down when the alt-hold is on

Aaand i found the problem, i put my lever max value at 1, completely my bad

It is better use the separate engine controllers for the each engine, since their RPS are not synchronized. Make sure the numeric value you connected to the desired RPS node is actually increasing as you increase the throttle.

Also where do i connect the RPS and Tempature to? If i connect it directly to the jet engine which part of the jet since im using this for a twin jet fighter

Not sure if its my fault or its a bug but whenever i try to put my throttle up my jet engine just stays idle, i may have wired it up wrong but idk, help would be appreciated :pray:

thanks i had no clue what it was doing 😅

Fixed, the pitch elevators should be at the tail.
https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=2892536322

that should be it thanks for looking at it i didnt expect you to reply so quickly reply at all

https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=2892527642

Yes, you can send me the plane via link in workshop.

if you need i can send you the plane and you can see