Stormworks: Build and Rescue

Stormworks: Build and Rescue

SBS HERMES Mk.I Medium Transport Plane (LEGACY)
11 条留言
TACOSAUCE 2019 年 3 月 30 日 下午 12:33 
This is the most detailed and complex flying craft ive seen in the stormworks workshop - good job!
Gibgib52 2019 年 3 月 24 日 下午 4:42 
thank you i went out of town so thats why the late reply
ElfBossHogg  [作者] 2019 年 3 月 23 日 上午 7:24 
Thanks for the comment, JVlaar. There was never an intention to copy a system. If LUCse feels slighted I apologise but the system I implemented (outiside of some calculations for AP from Tajin) is completely homegrown. The basis of it was built in mid January before the Pegasus even came out. Therefore I have no intention in removing it.
JVlaar 2019 年 3 月 23 日 上午 4:39 
I took a look at it the override code system, he uses a system that is quite different from the one you use in the bunker/fisher island, LUCse MENSEN
ElfBossHogg  [作者] 2019 年 3 月 22 日 下午 11:41 
Copy? There was no copy. I implemented the same code over ride system on my SCARAB submersible I implemented uploaded to the Workshop in Feb. I had it built mid January. It's all custom. I was not aware of any others. The HERMES uses the exact same code system Microcontrollers as the SCARAB. So please be careful when you are making accusations.
LUCse MENSEN 2019 年 3 月 22 日 下午 11:30 
Dude, why die you copy my code system?! I will strike you if you dont awnser in 5 hours! You have to renove it or give me credits for it!
ElfBossHogg  [作者] 2019 年 3 月 16 日 下午 8:52 
Thanks for you comment, gibgib52. To switch out of Idle mode there is a button between the Keys for Engine 2 and Engine 3 in the ceiling between the two pilot chairs. Click it (a toggle buton) to turn Idle mode off. It is set to Idle by default. Turning it off will transfer the Throttle controls to either the Manual Throttle between the pilot or the Hold Speed controls from the FBW (Fly by Wire) system.

Idle mode overrides all other Throttle calculation values for the engines as it is on a controller directly on the engines. It's give just the right amount of power for taxing on a runway so I find it very useful on the ground. I run Idle to get to my takeoff spot, dial the Manual throttle all the way up (which won't come in to effect until I turn off idle), turn off the brakes to start rolling again and then turn off idle which them pushes the engines to full throttle.
Gibgib52 2019 年 3 月 16 日 上午 10:46 
how do you switch out of idle mode? btw i love your creations
ElfBossHogg  [作者] 2019 年 3 月 13 日 下午 1:21 
Changed Override Code to 0397.
ElfBossHogg  [作者] 2019 年 3 月 12 日 上午 6:17 
Hi Ellak,

It's an Override Keypad for any locks on the hatches or doors. There are two buttons in the plane (one near the side door, one in the ceiling between the Pilot and Copilot's seat) that right now allow you to lock the side door and bottom hatch. In the future I will be adding a condition check where they may autolock while in flight. In implementing the lock the door condition lights will go Red and you won't be able to open them until the lock is removed... or you enter in the Override code. Which right now is 5468 but will change to a 4-digit number located "somewhere" on the plane... I think it's pretty easy to find.
Ellak 2019 年 3 月 12 日 上午 5:28 
Hi, i like the creation but what is the numpad code outside the plane?