订阅以下载
F-35B USMC (base)

United States Marines Corp painting
My ordinance collection : https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=2655522690
Preset of ordinances: https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=2620823773

almost 1:1 scale. (real scale)
Length : 15.75m (15.61m)
Width : 10.75m (10.67m)
Height : 4.5m (4.36m)

range : 350km (cruise), 100km (full throttle)
max speed : 269knot (flying),50knot (STOVL)
It has 4 chaffs and air to air refueling port.

• Current flight mode can be seen at the right panel seven segment. You should set idling when you change flight mode on the ground.
  0:CTOL, It completely performs as a aircraft.
  1:STOL([5]key), You can change rps from 10 to 40 to adjust speed or altitude. And you can change jet exhaust angle while cruise mode. Altitude hold is not available.
  2:STOVL([5] and [6]key), It cruises about 40knot and hold altitude.
  3:VTOL([6]key), It performs like a helicopter.
  
• Keyboard control
  
  a/d

  w/s

  left/right

  up/down

  CTOL

  roll

  pitch

  yaw

  throttle

  STOL

  roll

  pitch / nozzle angle (cruise)

  yaw

  throttle

  STOVL

  roll

  pitch

  yaw

  altitude

  VTOL

  roll

  forward/back

  yaw

  altitude
• Mouse control
  Level is updated when you activated mouse control mode ([2]key).
  Alt hold and heading hold are unavailable.
  
  a/d

  w/s

  look X

  look Y

  CTOL

  roll

  throttle

  yaw

  pitch

  STOL

  roll

  throttle

  yaw

  pitch

  STOVL

  roll

  altitude

  yaw

  pitch

  VTOL

  roll

  forward/back

  yaw

  altitude
• Flight assist
  These functions are available in only CTOL mode. You can see "{}" sign on the HUDs if they are active.
  Horizontal hold : When this function is active and you push neither [a]key nor [d]key, it keeps horizontal.
  Altitude hold : When this function is active, it holds altitude and you can change the setpoint by pushing [w]key(descent) or [s]key(climb).
  Heading hold : When this function is active and you push neither [left]key nor [right]key, it keeps the last pushed direction.
  Fix heading : You can fix target heading by keypad A value (0~360degrees). Touch (A) button on the biggest screen to update.
  STOVL cruise : When this function is active, you can change jet exhaust angle of the STOL. Or the speed setpoint of the VTOL mode becomes sticky.
  
• Trim
  You can fix angle or rotation speed by switching the trim flip switch on the right panel.
  It is reset when you switched off it.
  Roll : STOL or STOVL, VTOL
  Pitch : STOL or STOVL
  Yaw or Rudder : always
  
• Reverser
  When it is idling, it can go forward or back by ducted fan power.
  Just press throttle key while idling to use it.

You can switch map, fcs and assist, camera by touching bottom white lines.
Map explanation : https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=2730476986

You can select an ordinance by touching monitor. (White or dark gray 4px lines are selectable.)
You have to switch Master arm switches on the center panel to use selected hardpoint ordinances.
You have to switch Jettison or Jettison all switches on the center panel to release hardpoint ordinances.
You can use it by pushing trigger key.
Hold select : Touch HOLD button on the monitor to hold selection (hardpoint only).
Open bay : Touch BAY button on the monitor to open or close weapons bay manually.
Auto select : If it has a same ordinance, the fcs automatically changes hardpoint.
Click here if you'd like it to recognize any ordinance other people made.

Any ordinances can be launched without any remodeling.
It can launch any missiles or bombs made by other people.
It launches ordinance if the Ordinance Type is set "Unguided Bomb", "Laser Guided Bomb", "GPS Guided Bomb", "Rocket", "Laser Guided Missile", "GPS Guided Missile", "Radar Guided Missile", "Torpedo".
If hardpoint composite doesn't follow my FCS rules, disconnect the node or it doesn't work.
Auto switch is unavailable without remodeling to put an attachment below.
Amount indicator isn't available, too.

• Sending from the FCS
  On/Off 1:master arm, 2:trigger
  
• Return from an ordinance
  Number 1:ID, 2:current amount, 3:max amount
  On/Off 1:Active or not, 2:Ready or not, 3:Launch, 4:Lockable or not
  
• Rules
  Empty ID is 34~. (You can add more)
  Current amount and max amount must be at least 1.
  Detail : https://psteamcommunity.yuanyoumao.com/workshop/filedetails/?id=2655522690

You can see some information at 1*1 monitors.
You can change the visible information by touching small lines at the bottom of the monitors.
Detail : https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=2731055048

1. Fuel consumption and range, remaining time.
   
2. Simple radar. You can change display range.
   
3. Radar detector warns when the it detects 3sec constant radar wave. You can deactivate alert.
   
4. Beacon detector shows estimated beacon distance.
   
5. Map. It can zoom and scroll.
   
6. Camera : You can switch forward cam or bottom cam.

center HUD : https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=2136926352

Repaint is OK !
Re-uploading needs my permission ! Please contact me before uploading !