商店页面
Medieval Engineers
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Medieval Engineers

商店页面
Medieval Engineers >  创意工坊 > kcs123 的创意工坊
评价数不足
Truck 4x4 Large
描述 讨论0 留言8 改动说明
   
奖励
收藏
已收藏
取消收藏
Type: Blueprint
Version: 0.7
Blueprint Categories: Mechanical, Transport, Vanilla
文件大小
发表于
1.180 MB
2021 年 2 月 10 日 上午 11:04
1 项改动说明 （ 查看 ）

订阅以下载
Truck 4x4 Large

描述
On support to allow further development. Using 4 medium braking blocks and 2 extreme braking blocks.

Connect only one side of 1x pulley on rear shaft.
Connect 0.75 size pulley on front wheels on each side.
Connect 0.5 pulley on winch when you need it.

Only extreme braking blocks are in blocked position.

While it can achieve velocity above 40 km/h it is not recommended. More reasonable is 20-30 km/h when you can easy control vehicle. Anything higher is asking for trouble. Tested with 8 full loaded stone stockpile over steep slope on 25 km water planet. Estimated measurment of slope is ~25-30 degree (see pictures in gallery).
Using only one small steam engine.

4x4 drive wheels performs really good on slopes. I was surprised with results.
8 条留言
< >
onca77 2021 年 2 月 11 日 下午 2:18 
Essentially steam fails when the initial blueprint is too complicated.
kcs123  [作者] 2021 年 2 月 11 日 下午 2:08 
That is the second awesome advice today.Thanks, I was not aware of such shenanigans. Anotehr thing to remember for future updates.
onca77 2021 年 2 月 11 日 下午 2:04 
Ahh, this is a problem and needs care at the moment of pulishing for the first time. The solution is:
1. Blueprint and publish a simplest possible grid - a single timber or stone cube
2. Plueprint the grid you actually want to publish.
3. Update the steam version of the blueprint from 1 with the local blueprint of 2.
kcs123  [作者] 2021 年 2 月 11 日 下午 1:58 
I have recently asked for help on forum:
https://psteamcommunity.yuanyoumao.com/app/333950/discussions/0/3002178829578077622/#c3112519113947690556

Issue is taht I can't select some of properly published blueprints within game. Therefore I don't have option to update it. I didn't figured out reason behind it.
onca77 2021 年 2 月 11 日 下午 1:43 
Where the update fails exactly? Most common error is the thumbnail being larger than 1MB which system does not accept.
kcs123  [作者] 2021 年 2 月 11 日 上午 10:27 
I'm sorry, but as I was afraid, I can't update this or other recent blueprints for some reason. But at least I learned how to update some future blueprints that use pulleys in a way that connections are saved in the blueprint.
kcs123  [作者] 2021 年 2 月 11 日 上午 8:20 
I was not aware that you can make pulley connections twice, let alone that it helps in creating blueprint. Thanks a lot for that info, onca77. I will see if I can update at least some of my blueprints.
onca77 2021 年 2 月 11 日 上午 2:33 
If you make the pulley connections twice (so that three ropes are visible instead of two) the connections will be saved in the blueprint.