Stormworks: Build and Rescue

Stormworks: Build and Rescue

53 个评价
ENDAIR A321 XLR SKYCARGO
   
奖励
收藏
已收藏
取消收藏
文件大小
发表于
11.752 MB
2021 年 1 月 21 日 上午 1:00
1 项改动说明 ( 查看 )

订阅以下载
ENDAIR A321 XLR SKYCARGO

在 EnderPilot 的 1 个合集中
ENDAIR 1-1 Scale Aircraft
14 件物品
描述
ENDAIR A321 XLR SKYCARGO
The ENDAIR A321 XLR SKYCARGO is a freight aircraft developed by EPVIN Aviation Company
It has a Top speed of 310 Knots, has an [Xtra Long Range] from the 150,000 Liters of fuel in 2 wing tanks, one left and one right. Also features a realistic cockpit!
Also has a lower cargo bay in the galley and equipment closet an a avionics bay in the cockpit
And It can hold up to 10 Containers

[THIS AIRCRAFT IS COMPATABLE WITH AIR ISO COMPONENTS]

Discord
Official Discord Server : https://discord.gg/8YrrV9YJHM


[Requires modded workbench or custom mission to spawn]


NOTE: PLEASE DO NOT MODIFY OR RE-UPLOAD THIS VEHICLE


COCKPIT FEATURES:
* Analog and Digital Artificial horizon
* Map
* Fuel consumption Calculator
* Radio comutication for both pilots
* Autopilot, Altitude hold, Roll stabilisation
* a blackbox and flight tracking channel with frequency set to 19
* extendable-retractable Flaps
* extendable-retractable Spoilers
* extendable-retractable Landing gear
* Take-Give control to Captain or First Officer
* Fly-By-Wire Safety System [as featured in a real Airbus]
* Diching Mode [as featured in a real Airbus]
* Fire supression and test systems
* 3 hydraulic systems
* Cabin light and heating controls
* Nav, Strobe, Landing, Taxi and beacon lights
* Seatbelt and No Smoking Panel and warning
* Parking Brake

HOW TO GET IN:
Go to any of the front doors then press the button below the small window
and then jump and grab the handle next to the door button and bring your self up

STARTUP PROCEDURE:
1. Open Battery and avionics
2. Open All 3 PFD Controlers
3. Open all Hydaulic systems
4. Open EN1 and EN2 Fuel cutoff and pumps
5. Open EN1 and EN2 GEN and BUS
6. Open EN1 and EN2 Starters
7. Open Beacon

APU STARTUP PROCEDURE:
1. Open APU Fuel pump
2. Open APU Starter

AUTOPILOT SETUP:
1. Set up your waypoint coordinates on the Autopilot Coordinates Panel
2. Press the Engage Autopilot Button
3. Enable FD

ALTITUDE SETUP:
1. Set up your desired Altitude on the Altitude Hold Panel
2. Press the ALT HOLD Button
3. Enable FD

BLACKBOX AND FLIGHT TRACKING:
On channel: 19 there is a compisote signal transmition that holds flight information

THROTTLE:
*120% Takeoff
*110-80% Cruise [Its most eficient at 110%]
*30-25% Landing
*11% Taxiing


CREDITS

Billy-blij-1-2-3: Has offered great help with the New ALT HOLD AP Microcontroler!

3d MAP by Buunuu
CONSUMPTION 1x1 By krimwand
4 dials 1 display by michubushimax9

Consider leaving a Rating and a Comment if you like the creation.
If you find any Bugs please report them down below




热门讨论 查看全部(1)
4
5 月 18 日 下午 7:19
Next Aircraft Suggestion
EnderPilot
28 条留言
joona.player12 2024 年 1 月 30 日 上午 4:28 
uhh the flaps just open(to the sides) in mid air
sseeaann6 2023 年 9 月 15 日 下午 1:11 
what do i use to load it?
Chocolate Blaster 2023 年 5 月 27 日 上午 7:47 
1932_ford_3window_coupe Use the addon editor
L3nn0u 2022 年 11 月 17 日 下午 9:14 
what hanger should i use to spawn it (modded or nu modded)?
JaydenSKS 2022 年 9 月 18 日 上午 7:45 
Is there a heater on the plane?
NeptunetheBetta 2022 年 5 月 15 日 上午 11:12 
u should publish the catering truck:steamthumbsup:
JB-69 2022 年 5 月 7 日 下午 1:47 
cargo keeps derailing inside the plane after switching the direction of travel for the cargo.
team canada 2022 年 3 月 29 日 下午 6:12 
A310 next?
cally26311 2021 年 12 月 29 日 下午 2:16 
you didnt put the link how to in.
EnderPilot  [作者] 2021 年 10 月 25 日 上午 11:55 
you have to download the Air Iso stuff