商店页面
Stormworks: Build and Rescue
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Stormworks: Build and Rescue

商店页面
Stormworks: Build and Rescue >  创意工坊 > Uran_Wind 的创意工坊
43 个评价
ZE VTOL Framework
描述 讨论0 留言47 改动说明
   
奖励
收藏
已收藏
取消收藏
Vehicles: Vehicle, Air, Subassembly, Advanced
标签： v1.1.12
文件大小
发表于
更新日期
233.065 KB
2020 年 12 月 13 日 上午 11:28
2021 年 3 月 19 日 上午 8:47
14 项改动说明 （ 查看 ）
创建者
Uran_Wind
离线
查看所有 42 个合集（也许有些被隐藏了）
3,238 不重复访客数
1,162 当前订阅者
49 当前收藏人数

订阅以下载
ZE VTOL Framework

描述
A levitating framework for your vehicles like VTOLs, blimps, hovercrafts and airships.
  • Providing smooth tilt and yaw stabilization, idle position hold, manual and automatic altitude hold.
  • Exploits the game physics bug, where the wheels generate a phantom force if they are pushed with sub-bodies of the same vehicle.
  • Capable of carrying at least 20000 mass units and more.
  • Can turn across the yaw axis with roll tilt if moving forwards.
  • When horizontal mode is turned on, pitch tilt is disabled and propulsion value should be set to the horizontal mode throttle node, either with seat axis, lever or other numeric source.
  • Tilting and lifting accelerations are tuned by corresponding pilot seat axis sensitivity.

  • You can change the position of the wheel pushers by cutting and pasting them. I recommend to place them along the vertices of the rectangle, and the vehicle's center of mass should be at the intersection of its diagonals.
  • If there will be a weight disbalance, adjust the microcontroller pitch trim. Do not change the pilot seat axis trim because its nonzero values disables the automatic position hold.
  • Wheel pushers require at least 1 block of free space around them to avoid collisions.
47 条留言
< >
Zako 5 月 24 日 下午 11:37 
is there a way to make the altitude hold change faster? i was using it for something that requried fast changing in altitude hold
wolfee0507 2024 年 1 月 15 日 下午 7:37 
i kinda would like to be able to go fast with this?

what would i have to edit to make it go extremely fast? like 1000 miles per hour to 400 mph ranging around there or even higher speeds
AXEL_X 2023 年 8 月 13 日 下午 12:04 
Just wondering, it would be possible to use this with a 2 rotor setup? Currently working on a VTOL and i really can not make it work currently and looking for a microcontroller. Any suggestions?
kirb 2023 年 7 月 15 日 下午 11:55 
I have been experiencing the same issues as mark zuck-on-deez-nutz. Horizontal mode causes slight yawing.
Zuck on deez nutz 2022 年 3 月 9 日 下午 6:47 
when i turn on horizontal mode it kind of spins right (this is after i added an my own stuff)
skranwhite 2022 年 2 月 8 日 上午 3:14 
*pushes even when turned off
skranwhite 2022 年 2 月 8 日 上午 3:13 
Kirbcake, balance them relative to COM
Also, what to do if it pushes you vehicle to the side when on the ground
kirb 2022 年 1 月 11 日 下午 7:36 
So how do you get things made from this to be remotely stable? Anything more complex than a big cube and it just flips out and spins upon lifting.
Katsuragi 2021 年 10 月 29 日 下午 12:32 
and a life saver
Katsuragi 2021 年 10 月 29 日 下午 12:32 
your awesom