Stormworks: Build and Rescue

Stormworks: Build and Rescue

评价数不足
S76-D SAR Helicopter
   
奖励
收藏
已收藏
取消收藏
文件大小
发表于
更新日期
1.010 MB
2020 年 7 月 10 日 上午 10:26
2021 年 10 月 12 日 上午 7:25
13 项改动说明 ( 查看 )

订阅以下载
S76-D SAR Helicopter

在 ddeejjvviidd 的 1 个合集中
SR Transport
8 件物品
描述
S76-D SAR Helicopter

!1.0!

!OUTDATED PICTURES!

Have you ever wanted to have all round, fast, stabile and easily controllable helicopter? Well stop searching because you just found it. Go check it out. It flies smoothly and is so easy to control. Heli is powered by two jet engines with total fuel capacity of 13500l, which is enough to take you to the arctic and back. Heli has 3 winches, one witch harness, big one with magnet, and second smaller winch with electric connector. Heli can be refueled and recharged by connectors on sides. You can do everything with it. I hope you enjoy my creation.

  • Two jet engines

  • Fuel capacity 13500l

  • 6 passenger seats +(pilot and co-pilot seats)

  • 8 parachutes, 2 arctic suits, 1 diving suit, 2 firefighter suits and lot of 1.0 hand held tools.

  • Top speed: 205 km/h, 420 km/h in fast travel mode.

  • Long range rotatable stabilized camera.

  • Radio, channels 1-32

  • Big screen with 6 tabs - Settings tab, map, and 4 cameras. Map tab is defaultly shown first.

  • Heaters

  • Three winches.

Functions
  • Autoland, helicopter will automaticaly land when this assistent is turned on. Be aware to use it when you are above rough ground.

  • Auto landing gear, system will automaticaly operate with landing gear for you. Can be changed in settings.

  • Fast travel mode, throttle lever will unlock all the way up to 60 and helicopter will be able to reach top speed of 420 km/h.

  • Automatic altitude hold, this assistent will automaticaly hold current altitude when turned on.

  • Autopilot, this assistent will get you on selected waypoint automaticaly.

Start and piloting
For starting the engine, main circuit breaker needs to be turned on, then you need to turn on systems and then you can turn on start procedure, all by buttons on top middle panel.
Helicopter needs throttle at 40, so it can fly properly.
Control it by
W/S - Forward/Backward
A/D - Roll
Up/Down - Ascent / Descent
Left/Right - Yaw

[discord.gg]

DO NOT REUPLOAD WITHOUT MY PERMISSION
24 条留言
ddeejjvviidd  [作者] 2021 年 9 月 4 日 下午 12:35 
Or stick a control panel on the connector.
ddeejjvviidd  [作者] 2021 年 9 月 4 日 下午 12:35 
I dont think so. But you could make some timer that would lift the harness back up again automatically, after some time.
zachgauntlett 2021 年 9 月 3 日 下午 5:00 
Im a dunce and cant figure it out on my own despite hours of trying but is there any way you could make the winch able to raise and lower from the harness?
ddeejjvviidd  [作者] 2020 年 10 月 12 日 下午 12:42 
Vehicle has been reworked to 1.0. Sorry for delay
Quackoramic 2020 年 10 月 10 日 上午 5:42 
Yay
ddeejjvviidd  [作者] 2020 年 10 月 2 日 上午 10:33 
Okay good luck <3 currently working on upgrading it to 1.0 version
Quackoramic 2020 年 10 月 2 日 上午 8:26 
I know the heli by heart. It just stopped working suddenly. Gonna try again now!
XDerpingxGruntX 2020 年 9 月 24 日 下午 2:03 
yes, i followed the instructions to the tee.
ddeejjvviidd  [作者] 2020 年 9 月 24 日 上午 12:14 
Do you pull the throttle lever up to 40 before you take off? Cause it wont fly when its on 30
XDerpingxGruntX 2020 年 9 月 23 日 下午 5:13 
still won't work for me