Winkelpagina
Stormworks: Build and Rescue
Alles Discussies Screenshots Beeldmateriaal Uitzendingen Video's Workshop Nieuws Gidsen Recensies

Stormworks: Build and Rescue

Winkelpagina
Stormworks: Build and Rescue >  Workshop > Workshop van Uran_Wind
46 beoordelingen
ZE Airplane Flight Controller
Beschrijving Discussies0 Opmerkingen114 Wijzigingen
   
Prijs
Toevoegen aan favorieten
Toegevoegd aan favorieten
Verwijderen uit favorieten
Vehicles: Air, Mechanical
Microcontrollers: Microcontroller
Tags: v1.6.10
Bestandsgrootte
Geplaatst op
Bijgewerkt op
63.546 KB
19 jun 2020 om 12:03
27 dec 2022 om 9:26
15 wijzigingsnotities (weergeven)
Gemaakt door
Uran_Wind
Offline
Alle 144 verzamelingen bekijken (sommige zijn mogelijk verborgen)
7,273 unieke bezoekers
4,418 huidige abonnees
73 huidige favorieten

Abonneren om te downloaden
ZE Airplane Flight Controller

Omschrijving
Description
A full-fledged flight controller for airplanes with separate control surfaces. Providing smooth tilt and yaw, orientation hold, altitude hold, and has an optional engine control.
  • Engine, altitude hold and autopilot should be enabled manually through the composite node. On/Off channels for them are set in the microcontroller properties.

  • Engine control maintains the constant engine RPS and shut it down when overheating. Can handle with both diesel and jet engines. Also has a node for the jet turbine starter motors. Target RPS can set with a lever or a constant number.
  • The axis for Pitch/Prop and Roll/Yaw are switchable between WASD and arrows, pitch axis is invertible.
  • If altitude hold is enabled, airplane will be aligned horizontally and its direction can be changed only with yaw. If target altitude is set to 0, airplane will hold current altitude and the pitch axis is responsible for its vertical speed. Autopilot enables current altitude hold as well.

Setup order
  • Rotate roll control surfaces that way their orientations should be different.
  • Set propellers blade pitch to neutral.
  • Install this gyro and connect all logic nodes according their labels. Angular speed sensors should not be mirrored.
  • Set the correct control surfaces orientation in the microcontroller properties.
  • Connect pilot seat to the gyro with a composite link. Set all axis to the reset mode, adjust their sensitivity.
  • If you are using engine control, switch between propellers or jet engine type and set it's seat axis sensitivity to maximum.
  • Set seat axis trim to 0 and tune microcontroller pitch trim instead.

All done, but my airplane...
  • Tilts too slackly - increase the respective PILOT SEAT axis sensitivity.
  • Tilts too fast - reduce the respective axis turn speed.
  • Shaking with control surfaces - reduce the respective axis PID sensitivity.
  • Kicks back after yaw turn - reduce the PILOT SEAT yaw axis sensitivity or microcontroller yaw PID sensitivity.
  • Constantly pitching up or down - adjust the MICROCONTROLLER PITCH TRIM. Do not change the pilot seat axis trim because its nonzero values disables the automatic orientation hold.

Slim down basic controller with dimensions of default gyro.
114 opmerkingen
< >
Echoless 26 mei om 12:52 
Can you make this use the physics sensor
𐫱༺· V1RTU0US ·༻𐫱 30 apr om 3:18 
constantly rolls to the right a little bit
Uran_Wind  [auteur] 17 nov 2024 om 18:49 
yes
Slapsnake 17 nov 2024 om 16:44 
does this work for jet engines?
Mr. Clocks 7 aug 2024 om 5:05 
I think it would be incredibly useful if you could figure out some sort of custom gyroscope controller, since i've almost never been able to properly use the gyroscope
Uran_Wind  [auteur] 3 jun 2024 om 8:14 
Better to use a separate ECU.
TurtleUnit 3 jun 2024 om 3:50 
Does this work for Modular engines or am I better off using a seperate ECU?
Quantum toast 19 mei 2024 om 10:47 
what mode works with ducted fans or does that not matter if im not using the engine controller parts
Mrmunchyolly 19 nov 2023 om 23:50 
Will you ever make a new one of these?
Uran_Wind  [auteur] 16 nov 2023 om 12:17 
not really