商店页面

Stormworks: Build and Rescue

全部讨论截图艺术作品实况直播视频创意工坊新闻指南评测

Stormworks: Build and Rescue > 创意工坊 > Vad 的创意工坊

评价数不足

Bind (W/S) (Up/Down) to Throttle Lever

描述讨论0 留言11 改动说明

奖励

Vehicles: Sea, Land

Microcontrollers: Navigation, Modular, Microcontroller

标签： v0.6.20

文件大小

发表于

20.385 KB

2019 年 4 月 22 日下午 7:14

1 项改动说明（查看）

698	不重复访客数
287	当前订阅者
11	当前收藏人数

订阅以下载
Bind (W/S) (Up/Down) to Throttle Lever

已订阅

取消订阅

描述

Lets you bind (W/S) or (Up/Down), or both, to a throttle lever.
Size = 2x2

A few of the other solutions I found online didn't work well because they would set the throttle lever to fully on or fully off, this version allows precise control. You only need to attach the control system you want to use to one of the inputs, you don't have to attach both but it will work with both.

If you don't want the throttle to power down to zero every time you take your finger off the key, then:
- Open up your vehicle
- Use the select tool
- Click on your pilot seat
- Go into (w/s) or (up/down) and change the mode to "sticky".

11 条留言

< >

Leuri_Lentokone 2023 年 6 月 28 日上午 4:06

very helpful

Vad [作者] 2022 年 5 月 30 日上午 6:35

Thanks for letting me know but I don't mind. I posted a picture of the logic so people can make their own. I probably wasn't the first to make one either.

Ari Ari 2022 年 5 月 29 日下午 5:32

rere12 Stole this with no credits

warppioneer 2022 年 3 月 4 日下午 12:42

Thx! will be really helpful for my creation. I will credit.

PlatinumParakeet 2021 年 8 月 2 日上午 6:34

Thanks

Vad [作者] 2021 年 8 月 2 日上午 6:20

Two things I would check. 1) the throttle lever settings (double check you don't have any limits set) and 2) check the sensitivity on your pilot seat. High sensitivity might mess up the microcontrollers ability to measure the change in values when you press the button because your pilot seat will instantly jump from 0 to 1 when the microcontroller is expecting it to move smoothly.

If the problem was the sensitivity, you can lower the sensitivity or use a different microcontroller that does the same thing but doesn't use the "delta" (change) to do it. It's a problem I hadn't considered when I made it.

PlatinumParakeet 2021 年 8 月 1 日上午 6:44

It gets stuck at 0.02-0.03. Is this just an issue with my creation?

Inverspe 2021 年 2 月 11 日下午 8:57

thanks

coil_07 2020 年 8 月 13 日上午 9:02

thanks needed this for a plane

Nethiuz 2019 年 8 月 20 日下午 4:04

I use this in everything. Awesome job!

< >

Stormworks: Build and Rescue

订阅以下载Bind (W/S) (Up/Down) to Throttle Lever

编辑链接

订阅以下载
Bind (W/S) (Up/Down) to Throttle Lever