订阅以下载
[LR1 aser] BNSF GE Dash 9-44CW Train

[sws.flaffipony.rocks]

One of the rail cars used by the "BNSF" company
Model: "GE Dash 9-44CW" https://en.wikipedia.org/wiki/GE_Dash_9-44CW
Paint style: "Heritage II" https://en.wikipedia.org/wiki/BNSF_Railway#Paint_schemes



This train uses the Advanced Engine Mode!

• Auto throttle with slip control (select your target speed and the train will try to reach it)
  
• Pilot seat support (control the vehicle with keys 1-6)
  
• Special hull light effects
  
• Full walkthrough: Walk from front to the end of the train and even on connected waggons while driving
  
• Restroom with bed and outfits
  
• Arctic ready
  
• Compatible with my other waggons
  
• Remote control / Chaining: Chain as much of them as you want, in whatever direction you want and with any of my other waggons inbetween. Then control all from one pilot seat! (The only limit is your FPS)
  
• Maximum Speed:320 km/h or 200mph (needs 15 mins from donkk island to arctic)
  
• Fuel: 6000 (it is NOT enough to go to the arctic at full speed, drive slower and use only one motor then you will make it!)
  
• 2 Separate Energy production systems: Diesel Engine + Generator + Battery (Fully automatic)
  
• 4 Train wheel bases 1 Medium motor each (more traction and high speed)
  
• Emergency braking, Horn, far reaching light (Search light)
  
• Service doors for your engines
  
• Front and back lights (reacting to direction of movement)

1. Enter the control room
   
2. Use the left seat (Pilot seat)
   
3. On the right side enable key button "Main ON"
   
4. Enable the button bellow "Engines ON" to fire up the engines to produce energy
   
5. Release the brakes
   
6. Push the throttle
   
7. To drive backwards, hit the "reverse" button

You can do way more than just drive with a single vehicle!


To save fuel in idle mode you can kill the engines and just use the battery.
On the back wall in the control room you can enable the 2 independent energy production systems seperatly. Just enable one or both engines. Important: The power of both engines will not be enough to supply all motors at full throttle for ethernity. When the battery is running low on energy your motors will start to loose power until the consume the same amount your engines and generators produce.

The vehicle has 2 independent energy production systems (engine + generator + battery). Each system is connected to 2 electric motors to run the wheels.
By default both energy production systems are connected to the main energy net. You can disconnect both systems from each other, but that has no impact yet.

There is one backup battery ( a medium one) which can be connected manually to the rest of the electrical network. It can be used to fire up one engine after the other when your main batteries are depleted and cannot fire up the engines by themselves. Once all batteries are full again you should disconnect it again to be prepared for the next backup.

When chaining multiples of this vehicle (2, 3, 4 or more!):
We will call the vehicle you will control the complete chain "MASTER" from now on, all the others are called "SLAVES"
Spawn in a new vehicle and connect it one of both ends via the connectors
The direction of the vehicles do not matter
Do this for every SLAVE:

• Follow the easy startup procedure
  
• If the nose of this vehicle points into the opposite direction as the MASTER train, enable the "is reverse to master" button
  
• Enable "allow remote control". Once enabled the indicator near to it should light up green, if its yellow you have no connection to the MASTER train, check the connectors again.
  
• Disable the "reverse" button
  
• Disable the "emergency brake" (because this will override the remote brakes value)
  
• Apply brakes (so in case you decouple this train again it does not move away)
  
• Do this in the MASTER:
  
• Enable "control others"

Now you can release the brakes in the MASTER, push the throttle and here you go. Reverse will work like expected.

When chaining with other compatible waggons (see my collection):

• Enable "control others" button on the right hand side of the control room.
  This will allow you to release the brakes of every chained waggon.

--------

The couplers and size of the vehicle are now compatible with the Train Standards of the "Stormworks Rail Committee".

https://stormworks.gamepedia.com/Wiki/Standards/Land/Train