商店页面
Stormworks: Build and Rescue
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Stormworks: Build and Rescue

商店页面
Stormworks: Build and Rescue >  创意工坊 > Superlamaface #RelistWolves 的创意工坊
评价数不足
Plane Alt Hold
描述 讨论0 留言16 改动说明
   
奖励
收藏
已收藏
取消收藏
Microcontrollers: Calculation, Navigation, Microcontroller
标签： v0.6.9
文件大小
发表于
更新日期
28.061 KB
2019 年 3 月 17 日 上午 8:23
2019 年 3 月 17 日 上午 8:56
3 项改动说明 （ 查看 ）
创建者
Superlamaface #RelistWolves
在线
查看所有 17 个合集（也许有些被隐藏了）
1,760 不重复访客数
714 当前订阅者
3 当前收藏人数

订阅以下载
Plane Alt Hold

描述
Note 1
This controller should only be turned on near the wanted altitude if you want this process to be automatic look at the bottom for the linked secondary controller.

Note 2
The closer the tilt sensor is to the front of the aircraft the more responsive and touchy the altitude hold will be. If you are noticing swaying up and down around the desired altitude you may have to reposition your tilt sensor.


Setup Help
Make sure the tilt sensor arrow is facing toward the front of the plane and be on the horizontal line or x-axis like shown under here in text.

Front

/\
| Tilt Sensor arrow
|

Back


Secondary Controller
The controller linked below this will help with flipping. It prevents the Altitude Hold from activating to far away from the desired altitude causing flipping.
Link: https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=1999517057
16 条留言
< >
Superlamaface #RelistWolves  [作者] 2023 年 10 月 20 日 下午 6:30 
@jiri.kribek
The reason is you are activating the Altitude Hold to far away from the desired or set altitude. I have linked a secondary controller in the description which will help prevent this issue.

Here is the link to it though: Secondary Controller
jiri.kribek 2023 年 10 月 4 日 上午 11:27 
my plane keep doing loops why?
Messnot 2021 年 4 月 17 日 上午 8:24 
Thank you for this!!!!!!!!!!!!!!!!!!!!!!
Superlamaface #RelistWolves  [作者] 2020 年 7 月 28 日 下午 4:43 
Tigerlal
Yes it would
Tigerlal 2020 年 7 月 21 日 上午 3:59 
does this work for subs?
Superlamaface #RelistWolves  [作者] 2020 年 7 月 8 日 下午 4:50 
BOBBLMAN
Up/Down is reffering to pitch so for example if you want pitch to be W/S wire W/S to it for input.
Up/Down Output is what you connect to the control surfaces that it will use to pitch the plane!
The Great Rhombicosidodecahedron 2020 年 7 月 8 日 上午 12:19 
Up/Down Input and Output
The Great Rhombicosidodecahedron 2020 年 7 月 8 日 上午 12:19 
What do i wire Up/Down to? and waht does it do
johnkarpontin 2020 年 4 月 28 日 上午 8:58 
so i found a solution for the looping. just add a gyro to the mix and i will work just fine
Superlamaface #RelistWolves  [作者] 2020 年 2 月 16 日 上午 10:09 
Wilde_Insel
Use the other microcontroller I made today!
It will help with your issue