商店页面
Stormworks: Build and Rescue
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Stormworks: Build and Rescue

商店页面
Stormworks: Build and Rescue >  创意工坊 > Grimper 的创意工坊 > Ulysses Expedition Submarine > 讨论
Ulysses Expedition Submarine
描述 讨论5 留言359 改动说明
 此主题已被置顶，因此可能具有重要性
Grimper  [开发者] 2023 年 6 月 22 日 上午 6:19
Ramp issues
The cargo ramp is a bit...temperamental. Stormworks does not like it when grippers are so close to the ground and sliding through a narrow opening.

If the ramp gets stuck, try some of these solutions:

- Turn pivot power on and off
- Turn mags on and off
- Disconnect and reconnect the power cable (it attaches in the very middle block of the ramp)
- Close the door on the ramp, then open it again
< >
正在显示第 1 - 5 条，共 5 条留言
lechkingofdead 2023 年 6 月 24 日 下午 11:11 
is the ramp supost to remign in the up state when its slide out?
最后由 lechkingofdead 编辑于; 2023 年 6 月 24 日 下午 11:14
#1
Grimper  [开发者] 2023 年 6 月 25 日 上午 12:09 
引用自 lechkingofdead：
is the ramp supost to remign in the up state when its slide out?
Yes, it makes it easier to handle in narrow docks where you don't have the room to fully extend.
#2
lechkingofdead 2023 年 6 月 25 日 下午 5:30 
引用自 Grimper：
引用自 lechkingofdead：
is the ramp supost to remign in the up state when its slide out?
Yes, it makes it easier to handle in narrow docks where you don't have the room to fully extend.
ya i was just being a little derpy did not notice how the ramp exists :P i learned AFTER i feel into a gap of one after i got it to lock right. so i learned how it works
最后由 lechkingofdead 编辑于; 2023 年 6 月 25 日 下午 5:31
#3
DoneSonBoi 2023 年 7 月 3 日 上午 10:28 
I can't make the ramp go out.
its gets stuck at the electric connecters, and doesn't close or open after that.
I'm just trying to send the helicopter out, so I don't crash into the shallow waters.
How do I disable these electric connecters can someone please tell me.
#4
Grimper  [开发者] 2023 年 7 月 4 日 上午 12:23 
引用自 DoneSonBoi：
I can't make the ramp go out.
its gets stuck at the electric connecters, and doesn't close or open after that.
I'm just trying to send the helicopter out, so I don't crash into the shallow waters.
How do I disable these electric connecters can someone please tell me.

The ramp follows a complex sequence, in a very specific order, to deploy and undeploy. Very occasionally something can happen to mess up this order (like damage to the microcontroller, or a large wave/tsunami) and the ramp gets confused.
At this point usually the only way to fix it and get it back in the correct order is to respawn the vehicle. Even if I included a way to disable the connectors, the ramp still wouldn't work properly.
最后由 Grimper 编辑于; 2023 年 7 月 4 日 上午 12:24
#5
< >
正在显示第 1 - 5 条，共 5 条留言
每页显示数： 1530 50