安装 Steam						
					
				
				
									登录
											 | 
						语言
						
																																															繁體中文(繁体中文)
																													日本語(日语)
																													한국어(韩语)
																													ไทย(泰语)
																													български(保加利亚语)
																													Čeština(捷克语)
																													Dansk(丹麦语)
																													Deutsch(德语)
																													English(英语)
																													Español-España(西班牙语 - 西班牙)
																													Español - Latinoamérica(西班牙语 - 拉丁美洲)
																													Ελληνικά(希腊语)
																													Français(法语)
																													Italiano(意大利语)
																													Bahasa Indonesia(印度尼西亚语)
																													Magyar(匈牙利语)
																													Nederlands(荷兰语)
																													Norsk(挪威语)
																													Polski(波兰语)
																													Português(葡萄牙语 - 葡萄牙)
																													Português-Brasil(葡萄牙语 - 巴西)
																													Română(罗马尼亚语)
																													Русский(俄语)
																													Suomi(芬兰语)
																													Svenska(瑞典语)
																													Türkçe(土耳其语)
																													Tiếng Việt(越南语)
																													Українська(乌克兰语)
																									报告翻译问题
							
						
 
											 
													







Can you make a curve, 4x4 large blocks wide in both single and double stripe please?
http://pic20.picturetrail.com/VOL254/1944025/3755487/414272472.jpg
I'd like to be able to place one of these down as a curved taxi way marking onto a runway. ;)
Many thanks in advance!
Woostyboy.
Each of these takes like 10 minutes to make, but if I make any mistake, even a small one I will have to go through each of the variations I just worked on to double check whether I have done the same mistake there and then time piles on XD
This was supposed to be a quick "couple of hours" project but it ended up being 20-30 hours :P
Any chance that you could make a point light that is offset to one corner of a normal sized block? And eventually even amke more lights that follow the block edges, and lights embedded in blocks so you place the block with the light?
I have now updated the mod. It should now allow you to grind and weld them on the ground without having to remove the block it is attached to.
I have also added another "Rounded corner" variation of all blocks.
The updated version will have the same definitions so you can use this as much as you want :)
I will have to choose between having the Collision Model conform to the model or you able to grind / weld it.
I am testing my new collision models and the new models, but there is just an issue with having so small models.
I will ask you guys that reads this, do you think this mod even needs build states? I am trying to keep the mod as small as possible and I think the best way would be to not have build states. If I add build states it will most likely just the same model single colored as I am optimizing this for performance.
Can you please make all the dashes and characters you just made again, just make oblique? (Sloped) And can you please also add straight and oblique (slope) arrows? I use your mod as dashes for streets, on which later vehicles should drive. For this I also need oblique (slope), otherwise a curve is angular (edge). I'll pay you some money for it.
All crashes are epic until autosave does it thang right after. X.X
@SioxerNic HAPPY NEW YEAR TO YOU AS WELL. :D
.........It was a pretty epic crash though.
will they get damaged if [points at another engineer] that moron tries to land his speed because the Thrusters are too close to the ground.
can be they be damaged by thrusters?
i do know fully built heavy armor blocks are immune to thruster damage.
Will work on it next year.
Thanks for your link, I am already subscribed. What is your intent?