i dont know why, but when a pawn mutates, the mutations tap never updates. They never return to Human and the Mutations tap is also still empty, no matter what i do.

Where is hellhound injector? or am i blind?

Greatly yeah, I can't tell if it's exactly because of pawnmorpher or HAR but Pawnmorpher is the only mod I need HAR for nowadays... Anyways, it seems like pawn rendering might be slowing down game FPS a lot, not to mention for me all the additional menus on pawns with mutations seems to be broken too. I love the mod a lot but it does seem like it is hampering performance way too much at the moment.
To be clear, this isn't factual knowledge, I just observed some stuff in my very modded up playthrough, I didn't do a lot of testing or have the know-how to pin down issues like this anyways.

Yup performance has degraded somewhat since the last time I used this.

for some reason this mod causes the game to run very much slower when enabled

I feel that the 1.6 version can cause obvious more view drag lagging than 1.4 version. I have been playing this mod in 1.4 when there are about 300 mods and 80 colonists in my base, but the view drag lagging is alright. However, in 1.6 it starts lagging significantly event in quick test with 50 spawned pawns.

The mod seems to be throwing erros with a good bunch of race mods that uses HAR.

actually nvm i figured it out.

for some reason it says that pawnmorpher isn't 1.6 compatible on my mods tab

Ah, thanks for spotting that. It founds its way back into the mod info file, you don't need hugslib, I'll remove that and make a quick edit.

Why does the mod loader says that this requires hugslib when on this mods page it doesn't say it under requirement?

Updated to fix the issue with 1.5 saves.

I was able to do a temporary fix myself by just getting the previous version, again, was just informing in case it hadn't been reported yet.

@Zehzi Redscale there's a temporary manual fix on the discord in #discussion, until I get home and post the fix to steam later.

Thank you for your hard work.

I love using Pawnmorpher for my mod list in Rimworld, but I figure it should be mentioned that I am playing on ver. 1.5. It appears that the latest update to the mod causes some sort of issue on game load (enough that it forces a wipe of the mod list back to base game + DLCs). I mention this in the event no one else has noticed this / reported it for investigation.

Thanks for letting me know, I've updated it.

And just as an aside, your link to Ko-fi doesn't land on your creator page, it just lands on the feed page, at least for me. Ko-fi lacks a search function (!) and Google doesn't get anything for creator name "mikerobe". I was wanting to donate because I love this mod and am so happy to see it updated to 1.6, but I'm a bit stymied now.

Updated. yay! Thank you for keeping this mod running, it's one of my faves.

Sweet! I will be able to enjoy this awesome mod again :D

thanks for your work. this is a really fun mod, hope it stays alive for a long time without it causing grey hairs of course.

yaaay thank youu^^^

thanks for the update

Woo! Thank you for the 1.6 update!

Pawnmorpher has been updated to Rimworld 1.6.

Changelog:

* Updated to 1.6

* Fixed surgeries without ingredients throwing errors.
* Fixed morphs being incorrectly considered invalid for caravan.
* Fixed severity meter stuck at 0 in part picker for un-mutated pawns.
* Fixed launch time scaling by number of HAR races.

(As mentioned, this was bascially only going to be a version update. Thank you for your patience, and thanks to Zera for working on this update! Please report any issues you find, especially if they are new issues in existing 1.5 games.)

@Mcozzy if you dont mind a manual instalation, try to get it from the github. warning, its verry verry bleeding edge as it were. so expect errors and if you can report them. you may save dev time later.

When its done.

When 1.6 bruh

I used to Love this mod. I am Happy to know my experiments will continue in the future!

Literally waiting for this to update to start a new game.
I hope the update adds more stuff to it.

Personally I hope fully changed pawns become a bit more useful.

ya know they say you cant rush good quality. This is a prime example. So long as its confirmed that the mod is not abandoned patience wont be in short supply.

Take as much time as you need

on dc is 1.6 working prototype

its not coming guys....BUT IT IS ADVANCING

those who are a shark plush:

Those who can't read:

1.6 ? :(

1.6?

wooow finally the light in the tunnel, thanks

Thank you for updating us on the update. I'm looking forward to it. And take too much time as you need 🙂👍

wow, awesome news, thanks for keeping us in the loop!

please update this mod so is not corrupted.

manmade horrors byond my comprehension 10/10

That is most pleasing to hear Yap! I look forward to it :D

The issue with HAR has been fixed, so it is now possible to update. We'll have something soonish. There's a very early, unstable test build available on the discord, which I don't recommend you add to an active save, I more mean that there is indeed life here.

o7
best mod

Pity. It was one of the first mods I downloaded.

It really sucks that this mod is probably over, there really was nothing like it

Ouch, that sucks! I hope you have some luck finding a workaround, I was really hoping to play a mad scientist again! Best of luck to everyone working on it!

Yeah, HAR having that issue is definitely painful, hope to see it get fixed and having Pawnmorpher see the current version of Rimworld. Definitely one of my favourite if not most favourite mod for Rimworld.

@Yap They also specified that the issue was recently fixed. :u Days ago, on the Discord. Deffers looking forward to the update going forward.