商店页面
Barotrauma 潜渊症
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Barotrauma 潜渊症

商店页面
Barotrauma >  创意工坊 > _]|M|[_ 的创意工坊
476 个评价
Wifi Camera
描述 讨论2 留言175 改动说明
3
3
2
3
   
奖励
收藏
已收藏
取消收藏
Item, Item Assembly
文件大小
发表于
更新日期
854.589 KB
2023 年 8 月 15 日 上午 6:57
2024 年 10 月 23 日 上午 6:44
11 项改动说明 （ 查看 ）
创建者
_]|M|[_
离线
查看所有由 _]|M|[_ 和其他人创建的 9905 个合集（也许有些被隐藏了）
54,329 不重复访客数
43,863 当前订阅者
2,061 当前收藏人数

订阅以下载
Wifi Camera

在 _]|M|[_ 的 1 个合集中
Barotrauma Deathwish
64 件物品
描述
A wifi/body cam:
Craft or find wifi cameras with configurable channels to broadcast in. They can be toggled on and off and require a battery to broadcast. Finally the captain can see what the divers are doing!
A camera monitor (also craftable) or periscope hooked to a wifi component is required to view the cameras.
A camera monitor assembly is included to quickly place it into your submarine in the sub-editor.

What's in it:
- Wifi Camera (Craftable)
- Wifi Surveillance Camera (Craftable)
- Camera Monitor (Craftable | Provides visual effects when used)
- Camera Monitor Wiring Diagram (Craftable | An ingame guide to properly wire the monitor)
- Camera Monitor Assembly for sub-builders

Important Information:
1. The camera UI interfaces only work in play mode!
Do not open the camera items with Rightclick->Open while in the build mode of the submarine editor. It will crash your game. If you want to pre-place cameras with batteries inside them on your submarine use Shift + drag and drop the battery onto the camera item instead. You cannot pre-define a channel on the cameras in editor. The channel needs to be configured while playing. The same applies to the surveillance camera. You can not wire it in the sub-editor. You have to wire it during gameplay instead!

2. You might need to configure Performance Fix.
Add the following to your high priority items list if you notice the mod is not working properly when having performance fix enabled:
- cammonitor
- wificam
- surveillancecamera
- wificampiratehelmet
- wificamballistichelmet1
- wificamballistichelmet2
- wificamballistichelmet3
- wificamchitinhelmet
- wificamironhelmet
- wificamclownmask
- wificamclownmaskunique
- wificamclowndivingmask
- wificamdivingmask

Credits:
- hUbert for the general idea and improved code
- Udrakan for the wifi component solution to make this possible
- Plasmori for the russian translation
热门讨论 查看全部（2）
4
2024 年 1 月 6 日 下午 10:25
Headset version (Not feasible :c )
Dr. Lillian
0
2024 年 7 月 20 日 下午 3:24
Translations
RexTollBar (Reiss)
175 条留言
< >
DefaultString 8 月 31 日 下午 1:35 
Make sure to change component properties as well, not just wiring
balderus 8 月 31 日 下午 1:21 
hey there, i cant figure out how to wire the components...i mean, i already do all the wire connection on the circuit box but still it doesnt working
Mr. Orgasm 8 月 31 日 上午 4:25 
This should be in the base game by default, awesome mod!
_]|M|[_  [作者] 8 月 24 日 上午 4:33 
I'm not sure how that happens. I can't seem to reproduce this issue.
Could you guys provide more information like:

- Was it a self-crafted monitor that was manually placed while playing or was it placed via sub-editor?

- If placed via sub-editor, was the assembly item used to have a pre-wired setup or did you manually place a new monitor and wire it?

- What submarine did you use and what submarine/turret upgrades did you buy in the previous round, before it turned into a periscope?
DefaultString 8 月 23 日 下午 6:32 
Camera Monitor turns into periscope when you install or switch some turrets on your sub, this happens because it is based on periscope.
ъ 8 月 15 日 上午 9:53 
есть гайд как подключить камеры я ниче не понимаю по этим фото
Anteater 8 月 2 日 下午 10:34 
Camera monitor was working fine, turned into a periscope after one of the level loads, it still works the same but its become a periscope that cant be detatched
Sirax 6 月 27 日 下午 9:18 
any reason my camera monitor turned into a periscope that isnt unattachable?
_]|M|[_  [作者] 6 月 17 日 上午 3:29 
@Lord: You can craft the Camera Monitor Wiring Diagram and equip it so see how to wire the monitor so it can cycle trough channels. It can probably be improved by now since the devs added more components, but I haven't gotten around to redo the wiring.
The absolute simplest setup is just hooking a memory component to the monitor channel input and configuring the value in the memory component to the desired wifi channel of the camera.
C-17.3 6 月 15 日 上午 11:46 
Bro make a tuto i dont understand