商店页面
From The Depths
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

From The Depths

商店页面
From The Depths >  创意工坊 > Afjklol 的创意工坊
评价数不足
UT8M2 Escutcheon IV
描述 讨论0 留言5 改动说明
   
奖励
收藏
已收藏
取消收藏
Blueprints: #blueprint, Advanced Cannon, AI, Medium, Missile, Simple Weapons
标签： land
文件大小
发表于
更新日期
121.332 KB
2022 年 5 月 23 日 上午 9:38
9 月 28 日 下午 12:27
6 项改动说明 （ 查看 ）
链接
在 Youtube 上 (External link)
创建者
Afjklol
离线
查看所有由 Afjklol 和其他人创建的 17 个合集（也许有些被隐藏了）
772 不重复访客数
955 当前订阅者
20 当前收藏人数

订阅以下载
UT8M2 Escutcheon IV

在 Afjklol 的 2 个合集中
Khertland Military (v4.2.7)
100 件物品
Khertland Army (v4.2.7)
73 件物品
描述
The UT8M2 is a upgrade to the UT8M1 Escutcheon IV tank. The first upgrade since the tank's introduction. Improvements include a better recoil absorption for more accurate follow on shots. To do this, the electronic components was streamlined so it takes up less space. Most noticeably, the tank features the addition of the new Parvus Guard hardkill active protection system, a derivative development of the Iron Guardian C-RAM system. It can only intercept a single missile at a time and so is easily saturated. However it has a near 100% interception rate and serve as an additional layer of defense for the tank although quite pricey. Nonetheless, the Parvus Guard hardkill system is a significant improvement compared to Khertland's previous two generations of APS. More importantly the tank has improved HEAT and kinetic protection. Particularly, the front turret side is now covered with new ERA blocks for added protection when engaging against multiple targets. The total upgrade package adds an additional 3.5k to the unit cost for a total of 24.5k per tank. The army considered this as acceptable but still sizable increase in cost, however the improvements are seen as worthwhile.

Basic specifications:
Cost: 24.5k
Blocks: 589
Weight: 87,932
Volume: 942 cubic meter
Length: 20m
Width: 9m
Height: 6m (roof), 9m (RWS)
Speed: 25 m/s

Gun:
Caliber: 304mm
Barrel Length: L/55
Projectile: Sabot head-solid-solid-base bleeder-9x casing
Rate of Fire: 15 rpm
Kinetic damage: 6200
Armor piercing: 62
Penetration: At least 1 layer of 4m HA beam

Armor:
Hull front: HA wedge-HA beam-HA pole-4 layers of HA beams-HA pole-HA beam
Upper glacis: 4m HA slopes-6 layers of HA beams-Metal and stone roof
Hull side: HA-Beam-HA pole-HA beam
Hull rear: 2m of metal
Turret front: 2 layers of metal mimics-HA-HA pole-4 layers of HA beams
Turret side: Metal or HA beam
Turret rear: Metal mimic blocks

Active Protection Systems:
Parvus Guard

Ratings:
Total firepower: 16.1
Missile: 0.06
APS: 15.3
Simple cannon: 0.74
Armor: 37.4% (9161 materials)

Update Compatibility: 3.5.5
-Mesh fix
5 条留言
< >
Afjklol  [作者] 2022 年 6 月 17 日 下午 9:22 
I quickly rigged a HESH spewing gun but didn't find the tank particularly vulnerable to it. I already employ 2 layers of poles as spaced armor. I'm curious to see what you used against it. Well HESH seem to eat HA armor quite quickly but I'm not sure if there's anything else I can do
Spartanjackwar 2022 年 6 月 17 日 下午 9:17 
I feel that. The only way I've found to efficiently avoid EMP is air-gapped armor, which is rather hard to jam into tanks in FTD.
Afjklol  [作者] 2022 年 6 月 17 日 下午 9:01 
I'll be quite frank, I have no idea how to effectively counter EMP. On the UT8M1 I used stone outer layer but learned that EMP doesn't care about insulation anymore, or at least in any meaningful effect. And surge protectors are just really expensive and half the time don't seem to attract the EMP away from vitals.
Spartanjackwar 2022 年 6 月 17 日 下午 6:48 
A good looking tank, but it's notably weak to HESH and EMP even as low as 120mm.
Commanderbuzzard 2022 年 5 月 26 日 上午 10:50 
Damn, I wish I could make land anything as good as the rest of you guys.