商店页面
Stationeers
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Stationeers

商店页面
Stationeers >  创意工坊 > The Pez 的创意工坊
评价数不足
Maximum Efficiency AC Controller - Outdated
描述 讨论0 留言15 改动说明
   
奖励
收藏
已收藏
取消收藏
IC Code
文件大小
发表于
更新日期
237.912 KB
2021 年 6 月 1 日 上午 9:13
2021 年 6 月 3 日 上午 1:34
2 项改动说明 （ 查看 ）
创建者
The Pez
离线
查看所有 4 个合集（也许有些被隐藏了）
1,244 不重复访客数
209 当前订阅者
25 当前收藏人数

订阅以下载
Maximum Efficiency AC Controller - Outdated

描述
Controls the input of an AC unit so the is always achieves the selected output temp. Connect the input and waste for only 300W power usage. Waste/Input pipe line needs to be above 100kPa for the AC to actually output gas. Setup shown in the pictures above
15 条留言
< >
The Pez  [作者] 2022 年 11 月 15 日 下午 5:53 
No, the AC unit was completely reworked
AceTheRev0 2022 年 11 月 15 日 下午 3:30 
Does this work with the new update?
The Pez  [作者] 2022 年 5 月 20 日 上午 4:36 
Just copy the settings of the first one to the second.
Leiden 2022 年 5 月 20 日 上午 4:10 
How would I get the second air conditioner to copy the other one ( cooling ac 1 and 2 ).

Ps. I'm rather new to Ic
maxdreamland 2022 年 2 月 2 日 上午 9:03 
ahh, looks like the whole thing starts to behave more normally once you start actually extracting heat from the hot side. once i attached a heat exchanger the crazy temperatures went down withing seconds. probably some kind of glitch...they were up to over 100K C before, though :-D
maxdreamland 2022 年 2 月 2 日 上午 8:47 
maybe i still have something wrong, but it seems to be wrong in a glorious way :-) my cold side is now cooling, its at -55 C by now. But the hot side is REALLY getting hot. It's currently at 36k C ... yes, thats 36 THOUSAND! And the rate in temperature change is accellerating the hotter it gets! I'm actually kinda scared where it might go if i let it. weird thing is, the pressure stays constant at around 300 kPa and the moles in the hot tube are constant as well. how is that even possible? with the same amount of moles, same volume but rising temperature the pressure should be rising, too, right?

you could probably build a perpetual motion machine, using the heat to get power from a stirling engine for example. i bet you get more than the ~650W you need to run the A/C's out of the 36K hot gas :-)
maxdreamland 2022 年 2 月 2 日 上午 8:30 
you might have made the same mistake that i did initially. what the IC expects as the hot pump is actually the pump that sits on the cold side, and vice versa. look at the screenshot...the blue pump is in the red pipes and vice versa. after i fixed that it worked for me. before that i had the same symptoms you did.
Superbrain8 2021 年 11 月 30 日 上午 1:14 
yes, the volume pups run on 4L on the hot side and 3L on the cold side
The Pez  [作者] 2021 年 11 月 29 日 下午 4:50 
Not sure why, you may have the setup wrong if it never reaches 73.15K (-200C) on the cold side. For the cold AC to even output gas the hot side needs to be above 100kPa and the same for hot AC. Were you using insulated pipes?
Superbrain8 2021 年 11 月 29 日 上午 6:53 
works quite well for me, but it wont reach the wanted temperatures, idk if there is not enough gas in the system or just the world being funky (had this on a custom world where it just acted weird). cold side sits around 900kPA and the hotside around 2MPA