商店页面

Stationeers

全部讨论截图艺术作品实况直播视频创意工坊新闻指南评测

Stationeers > 创意工坊 > 123 的创意工坊

86 个评价

[F&S] Solar Panel Tracking

描述讨论0 留言40 改动说明

奖励

IC Code

文件大小

发表于

更新日期

20.142 KB

2019 年 3 月 30 日上午 7:50

2022 年 6 月 3 日下午 9:10

16 项改动说明（查看）

11,180	不重复访客数
3,374	当前订阅者
159	当前收藏人数

订阅以下载
[F&S] Solar Panel Tracking

已订阅

取消订阅

在 123 的 1 个合集中

[F&S] Advanced Devices

14 件物品

描述

Description

Tracks the position of the sun, at night moves to the position of the sunrise. Optionally can turn on the light at nightfall, at the beginning of the morning, turns off the light.
Works for Moon, Mars, Europa, Vulcano, and any modified suns angle.

Requirements

1 Daylight Sensor.
1 IC Housing.
1 Integrated Circuit (IC10).
1 Area Power Controller.
1 Battery Cell (Large).
At least one Solar Panel. (Supports both versions, normal and heavy panels)

IC ports description

Port

Device

Daylight Sensor (Optional not required)

Dial (Optional not required. Controls the horizontal angle of the solar panels)

Night Signal (Optional not required)

Changeable values in IC code

define SolarHorizontalAngle 0 define EveningMorningAngle 85 #90=night,85=twilight

SolarHorizontalAngle - acts like a dial if you don't want to build it
EveningMorningAngle - Turns on the light just before dark. (90+ mean sun below the horizon). You can set a value less than 90, then the light will be on until the night appears.

D1 Dial settings

You can place the panels as you like, but you need a dialer to adjust their angle. (All panels should be located at one angle.)

0: 0
1: 90
2: 180
3: 270

If you don’t want math, mount and turn the dial until the result is achieved.

D2 Night Signal

1 - At sunset and all night.
0 - At sunrise and all day.

Turns on the specified device at sunset and off at sunrise (Holds device state On or Off.). You can use any device that supports On/Off or you can use memory chip, and read value from another device.

Note

You must place the sensor in the correct position, see the pictures.
All panels should be located at one angle.

Game version support

0.2.5116.23239 05/08/2024

40 条留言

< >

G0tY0urB@cK 9 月 23 日上午 9:09

Peeps been using this for 2 years now. its super easy look at the pics copy, done

dzlockhead 2024 年 8 月 16 日下午 6:09

Oh strange, for me it was necessary, it didn't work until I set d0 to the sensor

123 [作者] 2024 年 8 月 14 日上午 1:00

dzlockhead,

Requirements
1 Daylight Sensor.

IC ports description
D0 Daylight Sensor (Optional not required)

This means that it is not necessary to set the sensor on port D0 with a screwdriver, the IC will detect it automatically in the connected network. (This is sometimes necessary)

About the images, this is what the daylight sensor looked like in 2019.

A lot has changed in 5 years....

dzlockhead 2024 年 8 月 12 日上午 11:25

Yep, I can confirm it still works but the daylight sensor is REQUIRED on D0, unlike what is said in the description. Also the images showing sensor direction should be said Daylight Sensor, NOT a motion sensor as pictured.

123 [作者] 2024 年 8 月 10 日下午 7:43

Tested on latest version 0.2.5116.23239 all work fine.

Error on line 40, means the daylight sensor was not found.

Squama, you can adjust horizintal angle by dialer or in code. Check "Changeable values in IC code" in this page. No need rotate panels, you can place panels as you wish. (But all power outputs must be on the same side)

dzlockhead 2024 年 7 月 29 日下午 10:04

Same, error on line 40