商店页面
Prison Architect
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Prison Architect

商店页面
Prison Architect >  创意工坊 > SHOT(by)GUN 的创意工坊 > BlastDoor > 讨论
BlastDoor
描述 讨论10 留言274 改动说明
 此主题已被置顶，因此可能具有重要性
SHOT(by)GUN  [开发者] 2015 年 1 月 2 日 下午 9:53
Basic Tutorial
Quick Checklist:
1. Have you subscribed to the mod at steam workshop?
2. Have you enabled the mod inside the game?
3. Have you installed the Blast Door?
4. Have you installed Servo attached to the Blast Door?
5. Is the Servo powered ?
6. Have you connected Power Switch to the Blast Door ? (not the other way around)
7. Have you tried switching the Power Switch on/off ?

Blast Door functions basically same like the Remote Door, except Blast Door does not work with the Remote Control panel.

Full instructions how to operate the blast door with pictures are available at this link:

Click here >>> http://imgur.com/a/TGqkO <<<
最后由 SHOT(by)GUN 编辑于; 2015 年 1 月 2 日 下午 10:23
< >
正在显示第 1 - 11 条，共 11 条留言
The Strategist 2015 年 1 月 6 日 上午 6:15 
i installed the door + servo and the servo is powerd + the power switch is connect to the blast door but still it does not open. I did a second time totally the same but still it does not work
#1
The Strategist 2015 年 1 月 6 日 上午 6:16 
PLS help
#2
Maxumus2001 2015 年 1 月 7 日 上午 12:09 
Connect the switch to the servo it might help
#3
Gbarker2000 2015 年 2 月 21 日 下午 9:28 
Will not open for me no matter what and my workers won't disable or dump it. It has crippled my prison since it is right where all my workers and guards need to travel through to get to the armory and solitary.
#4
Javascap 2015 年 4 月 6 日 下午 3:29 
Does it work with the Door Control System? I've not had any luck with that. It works fine with the Power Switch.
#5
Rusty Robot 2015 年 10 月 27 日 下午 6:23 
It definitely seems to work with the power switch. Thanks for making this little troubleshoot guide, I was tearing my hair out trying to figure out why door control wasn't working.
#6
Maximus 2016 年 3 月 30 日 下午 3:28 
引用自 戦闘機の楽しみ：
i installed the door + servo and the servo is powerd + the power switch is connect to the blast door but still it does not open. I did a second time totally the same but still it does not work
did you add a power switch then connect it to the servor
#7
samutrai ✨ 2017 年 6 月 4 日 上午 9:31 
ur should put it to remote cotrol panel, cuz it would be usefull
#8
Club Ardi 2017 年 7 月 4 日 上午 9:02 
it works for me, just connect the power switch to the door servo(s) and it will be done. be sure to connect the powr thx:steamhappy:
#9
FlexySpagoot 2017 年 7 月 12 日 下午 5:16 
That link is very helpful mine was useless, I had it connected to pressure pads and a logic bridge and a switch
#10
peterfield 2018 年 5 月 15 日 上午 11:23 
Is there a way to make this work with escape mode?
最后由 peterfield 编辑于; 2018 年 5 月 15 日 上午 11:24
#11
< >
正在显示第 1 - 11 条，共 11 条留言
每页显示数： 1530 50