商店页面
Space Engineers
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Space Engineers

商店页面
Space Engineers >  创意工坊 > Naz 的创意工坊
71 个评价
Bulldog Armoured Personnel Carrier (No Mods)
描述 讨论0 留言10 改动说明
   
奖励
收藏
已收藏
取消收藏
Type: Blueprint
文件大小
发表于
2.201 MB
2019 年 10 月 30 日 下午 10:58
1 项改动说明 （ 查看 ）
所需的 DLC
此物品需要下列所有 DLC
Space Engineers - Decorative Pack #2
创建者
Naz
在线
查看所有由 Naz 和其他人创建的 51 个合集（也许有些被隐藏了）
3,525 不重复访客数
1,028 当前订阅者
101 当前收藏人数
您需要 DLC 才能使用该物品。

订阅以下载
Bulldog Armoured Personnel Carrier (No Mods)

在 Naz 的 1 个合集中
NSSMC - Northern Surface and Space Military Corporation
39 件物品
描述
Bulldog Troop Transport Rover

Vanilla, Survival Ready



Cheap and easy to build, the Bulldog APC allows for quick reproduction, all the while being a highly versatile rover. The vehicle features a troop capacity of 4(excluding the driver), has a piston for maintenance and other equipment such as a small cargo capacity and medical bay, allowing for health regeneration and respawning of troops. Can also be airdropped from a height whilst landing softly with an installed parachute system.



Uses Decoration Pack II. If you do not own it, you can still use it, but you'll have to place a cockpit from the missing space in the cabin. The other DLC blocks won't break the vehicle when spawning, as they are just LCDs.


Mass (Empty): 68 Tons
Armor: Light
Power: Hydrogen & Battery
Thrust: Wheels
Armaments: x1 Gatling Turret
Handling dificulty: Very Easy
Area of operation: Surface - Earthlike/Alien/Mars etc

Check out my other works:
Tornado III Atmo Fighter: https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=1900078437
'Filibuster' Frigate: https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=1738023618
'Reynard' Corvette: https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=1714066629
'Robin' Light Interceptor: https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=1707854864
Follow my workshop page!


10 条留言
< >
Naz  [作者] 2019 年 11 月 7 日 下午 8:22 
Many thanks :)
Unknownsmile 2019 年 11 月 7 日 下午 7:15 
You did an amazing job making the interior portion very realistic. I'd love to see more rover vehicles and will be checking out your other creations. bravo Nazz
Naz  [作者] 2019 年 11 月 7 日 下午 7:05 
It certainly does have a really low base clearance, I nearly ran out of room trying to place the interior lights(the ceiling lights are actually non-illuminated LCDs).
Unknownsmile 2019 年 11 月 7 日 下午 4:32 
Scratch my last comment. Apparantly after many attempts, the wheel settings were not synced together and it was the power setting that had to be adjusted.
Unknownsmile 2019 年 11 月 7 日 下午 4:25 
I built this in survival with the wheel settings set back to your settings. However, the back of the rover is too low to the ground, causing it to drag its rear end to the ground. I tried messing with the settings but nothing seems to fix this issue. The front is fine and all wheels have the same settings.
Sevyrs 2019 年 11 月 2 日 上午 11:30 
VERY NICE!
Naz  [作者] 2019 年 11 月 2 日 上午 3:24 
@5URG3 Thanks mate :)
5URG3 2019 年 11 月 2 日 上午 2:07 
I like this. Nice build!
Naz  [作者] 2019 年 11 月 1 日 下午 8:31 
@Delta Hawk Thanks for acknowledging. The rover's interiors are not pressurized.
Delta Hawk 2019 年 11 月 1 日 上午 9:33 
You shouldn't need the DLC for this now since Keen moved the small seat over to vanilla. It is air sealed?