상점 페이지
Medieval Engineers
전체 토론 스크린샷 아트워크 방송 동영상 창작마당 뉴스 가이드 평가

Medieval Engineers

상점 페이지
Medieval Engineers >  창작마당 > peaceman 님의 창작마당
181 평점
Balloons
설명 토론0 댓글211 업데이트 노트
   
어워드
즐겨찾기
즐겨찾기됨
즐겨찾기 해제
Type: Mod
Mod category: block, script, modpack
Version: 0.7
파일 크기
게시일
업데이트일
12.668 MB
2017년 11월 7일 오후 3시 23분
2025년 6월 23일 오후 3시 07분
업데이트 노트 130개 (보기)
필요한 아이템
이 항목에 필요한 다른 항목
제작자
peaceman
오프라인
모음집 373개 모두 보기 (숨긴 상태 몇 개 있을 수 있습니다)
15,005 순 방문자 수
10,745 현재 구독자 수
323 현재 즐겨찾기 수

다운로드 위해 구독하기
Balloons

설명
This mod adds Balloons to Medieval Engineers

Place some fuel inside, light it and use the paddle to increase its lift. Each balloon has a maximum lift of ±1500kg at ground level, the higher you go the less lift it will have. Don't worry, even with no load your balloons will never reach space !

Make sure your balloon is attached by a rope or it will fly off until it runs out of fuel. Even after it runs out of fuel it will slowly decent again.

When designing your flying stuff make sure you can reach your balloon to change the lift or refueling. If not you can always use chests to change your altitude.
Creating and flying balloons will be a learning experience, especially in survival. (creating flying castles with catapults IS possible)

This mod also adds a propeller to turn and move your craft while in the air. Attach it to a catchblock and make it spin ! the faster it spins the more thrust it provides.

Check out the player harness mod: http://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=1199350061
It allows you to attach yourself "safely" to any grid or even launch yourself.

If you like my mods, consider sending me some love -> [www.paypal.com]
댓글 211개
< >
peaceman  [작성자] 2022년 9월 12일 오전 9시 07분 
Contact me on discord, I will send you the blender file of the model
SicH 2022년 9월 11일 오전 2시 24분 
how about turbine props with variable diameter? To don't have square "engines" with 4 subgrids for airliners. But to have one 9.5-10 small blocks prop, placed inside the round "engine". Or to be able to place smaller "engines" for regional jets / fighter jets / etc. Could do it by myself, but I don't have any opportunity to scale the original model. The only way to scale it afaik is scaling the model before processing into .mwm
gabgab01 2022년 7월 21일 오전 11시 52분 
i can understand that it's intended, but in reality it's kind of a balancing issue.
because if you use a large balloon, you end up having to add a lot of weight / mass in order to even be able to land it, which in turn increases the total mass, and you need bigger / more steam engines to even propel it, which in turn makes it even heavier and slower again, and so on.

and at those sizes it starts afflicting the sim speed on servers.

nevertheless, it's still an awesome mod!
peaceman  [작성자] 2022년 7월 21일 오전 9시 12분 
You mean with the heat panel closed? This is intended. Not all heat is blocked so the balloon still has some lift. I think its like 25% of max lift
gabgab01 2022년 7월 3일 오전 10시 22분 
the balloons never have 0 lift when they're turned on.
i always need a crate full of ore to even be able to land with the big balloon. otherwise i'd be stuck at a height of 450 metres on minimal lift, which makes these even more expensive in survival :D
Terradus 2022년 6월 19일 오전 5시 54분 
@peacema
Why for this mod need steam engines mod ? Can you please create "balons" mod without dependencies with "steam engine" and "Pulleys" mods ?
peaceman  [작성자] 2021년 7월 13일 오전 11시 28분 
Drafting table
Hoplite 2021년 7월 13일 오전 8시 40분 
so where i can get blank scrolls
Hektor Riven 2020년 10월 30일 오전 11시 33분 
The balloon "breaks" without noise or animation: just disappears with the rope and its eye plate.
I've considered to place the balloon directly on the grid, however I was never able to do it but once, and just for a small grid attached to a large grid standing on the ground. Adding the balloon to a free grid seemed to be impossible for me, but I'll keep trying.
Thanks again for your support!
peaceman  [작성자] 2020년 10월 30일 오전 9시 29분 
I see, it breaks the balloon when the rope breaks? Or does the balloon just fly off into near space? :D
I suggest not using ropes. Just attach the balloon directly to your grid. Place it above center of mass then all should be stable