This is the ATV-M-1010 crawler or All terrain vehicle-Medic-1010 Crawler

It features a total of:
6 T10 nano tech guns
5 T10 walker legs
1 T10 electro plate R
1 T10 electro plate L
2 T9 electro plate L
2 T9 electro plate R
1 T7 electro plate L
1 T7 electro plate R
1 T9 radar
1 T9 radar jammer
8 Armored tetras
198 armored cubes

if you have all htis you are ready to build your bot.

1:the first step on getting the chassi built is you start by building a small frame around the piolet seat like this. make sure to leave those 2 spaces on the front and back open for electro plates will be filling in those spaces later


2:your next step is to add tubes of armored cubes on both the front and back. specificly 2 tall nad 3 wide. add 5 rows on hte back and 7 on the front. this is the main body that connects the front and rear componets


3:now go to the front of the vehicle and add these shown cubes 4 blocks out and make their rows 2 blocks thick. this will later hold 4 of your nano guns. make sure it starts one block behind the front block on the middle



4:after you have this done add a single thick line under the front side of what you have just created. fully connected accros the bottom.



5:now add some more armored cubes here. these will help armor and help hold your nano guns later on.


6:now on the back of this row add some armored tetras where i show here. if you have a lot lf CPU after the bot is done you can come back and make a full line of these to armor it if you'd want.




7: Now that the front of the body is done move to the rar end and add these few cubes.





8: after you have those added you will add some more on the sides as these are also gun mounts. this part is ticky because you have to leave 2 spaces directly below it so that a plate can fit under later and the second way out will be 2 thick but the first connection will only be 1.



9: after you figure out how that is layed out you now add soe more cubes to the direct rear like shown. in order to add armor and space to place future hardware.


10: the Final part of the chassi you have to put down is these last few cubes that will hold some hard ware. after this the chassi will be completed and you are ready to start adding the other componets.

1:So after you get your chassi done you go to the rear little hole you built in the beginning and you add both T10 electro plates. as shown.



2:After adding this you can proceed to adding the radar and radar jammer as shown before. if you messed up the complicated step in the chassi building you will not be able to fit these and you will have to modifie till they fit.



3:After you have those componets in you move on to the first of the frontal plates. these 2 T9 plates covoer the gun mounts and rear end from the front. place them as shown.


4:Now you move on to the T7 plates that will cover the front of the piolet and further protection over the frontal chassi as well. place them right infront of the piolet and previous plates.



5:Now you put the final 2 T9 plates on the front. these are the fore front of what is adsorbing your damage income and that gap in the front is neccesary for a future step. place as shown.


6:you will now add the first 2 nano guns on both sides on the top mounts on the mid section as shown. put the on the front block so that htey get the most out of the armor provided.




7:you now add 2 of the front mounted nano guns as shown below.




8: now you place the bottom 2 make sure to place as shown because in the later step they will not fit when the legs are placed if they are any closer together





9: After you have these places the final steps are simply putting the walker legs in. place legs on both sides as shown below.
[/previewimg





once you finish this your bot should look some what like this



if it looks like this you have finished yoru bot.

the crawler is a good medic design. using both good mobility for gioing any where but has a light weight design that is capable of taking light damage. a voley of plasma shells or a rail gun can cripple you if not kill you in one shot. so stay away from combat if yo ucan by staying behind cover wether its just on the wall or behind your teams mega bot or behind a rock to heal. the only tiem you should be able to go out into battle would be near the end of a challenge battle.
now while it may be fragile it makes up for thsi by its nano gun efficency having max guns and 4 of them pointing forward for good focus healing.


NOTES:
If you still have leftover CPU feel free to add armor where you feel is needed this is just a base version that conserves CPU while still having a decent amount of armor.

If you are wondering about the leg on the front well it is there because it gives more manuverability. its much easier to climb walls with the leg on the frong pulling you up. if you really want to im sure you could fit 1 or 2 tesla blades on the front. and put the leg on the back.



tell me what you think of my design and please dont copletely hate.