商店页面
Barotrauma 潜渊症
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Barotrauma 潜渊症

商店页面
Barotrauma >  创意工坊 > Working Joe 的创意工坊
26 个评价
Barotronics - Sequence Skip Airlock
描述 讨论0 留言12 改动说明
   
奖励
收藏
已收藏
取消收藏
Submarine
文件大小
发表于
更新日期
178.708 KB
2020 年 12 月 4 日 下午 6:52
2022 年 11 月 7 日 上午 11:39
3 项改动说明 （ 查看 ）
创建者
Working Joe
离线
查看所有由 Working Joe 和其他人创建的 145 个合集（也许有些被隐藏了）
2,092 不重复访客数
809 当前订阅者
54 当前收藏人数

订阅以下载
Barotronics - Sequence Skip Airlock

在 Working Joe 的 1 个合集中
Barotronics - The Collection
14 件物品
描述
The first of a series of circuits I previously made but didn't take the time to properly release, until now. :)

The Sequence Skip Airlock is the simplest to use airlock with decent comfort features. On pressing any of the buttons, both doors close and the airlock starts it's draining or flooding sequence. Once the airlock is fully drained or flooded, the inside or outside door will open respectively. If you're in a hurry - whether it's being chased by a tresher or the clown with the funny hammer - you can press the button again after a short time to skip the sequence, opening the door before the sequence is complete. This may let some water in, but that's what we've got bilge pumps for right?

I hope this will be of use to some of you!

-WorkingJoe

Note: If your airlock doesn't cycle properly (for instance it drains, but then opens once it's filled letting water in again) try switching around the doors. The circuit isn't entirely symmetrical.
12 条留言
< >
diogeek 2024 年 11 月 23 日 上午 11:28 
Very nice, ended my hours of struggle with a docking hatch airlock, 10/10 would recommend
Kaito 2022 年 12 月 30 日 下午 2:30 
Really nice stuff. Works most of the time. Sometimes it gets stuck and refuses to open the inner door, and the pump keeps trying to pump water out when the outer door is open, but it mostly works as expected. No idea how I could fix those, the circuitry is beyond me.
JangoXIII 2022 年 4 月 21 日 上午 9:09 
I was able to fix this by using the state of the outside door, a not component and set state of the pump to circumvent the oddity. take my points.
JangoXIII 2022 年 4 月 21 日 上午 8:59 
really cool airlock, mostly works, only caviat for me is im using the left most airlock diagram, and when it fills with water and opens the left door (i switched the doors around// open to outside) the pump fluctuates at -49 to -50 instead of turning off, so it is constantly running only when we leave the sub. other than that this is completely functional and exactly what I was looking for in an airlock.
Gejaheline 2020 年 12 月 21 日 下午 2:13 
Cool, I'll give it a shot, actual working airlocks seem to be a rare thing!
Working Joe  [作者] 2020 年 12 月 21 日 下午 12:17 
@Gejaheline The item should be updated now, there was a signal check missing so while the docking would override both doors to be open, it would put the airlock in the full state rather than the drain state :)
Kafson 2020 年 12 月 12 日 上午 6:57 
Just tried it out. It consantly drains and fills the airlock and ejects the water after filling. Is that intended?:captainsinful:
Working Joe  [作者] 2020 年 12 月 11 日 上午 10:09 
@Gejaheline Woops, I'll have to look into that. Probably something I broke when moving the contraption around to display it. There should be some signal from the state_out of the docking port that sets the pump target level to -50. I'll see if I can update it later.
Gejaheline 2020 年 12 月 10 日 下午 2:36 
Addendum to previous comment: Connecting the docking port's signal relay directly to the pump's signal relay fixed the issue (until someone pressed one of the airlock cycle buttons), so that's a partial solution.
Gejaheline 2020 年 12 月 10 日 下午 12:35 
The standard option works excellently, but the "open both doors when a shuttle is docked" version appears to open both doors and sets the pump to fill the room with water when a shuttle docks, when it should be emptying.