상점 페이지
Arma 3
전체 토론 스크린샷 아트워크 방송 동영상 창작마당 뉴스 가이드 평가
Arma 3 >  창작마당 > Steve 님의 창작마당
87 평점
ACE3 Compatibility for SPS AI AXMC Sniper Rifles
설명 토론0 댓글9 업데이트 노트
   
어워드
즐겨찾기
즐겨찾기됨
즐겨찾기 해제
Data Type: Mod
Mod Type: Mechanics, Weapon
파일 크기
게시일
업데이트일
1.008 MB
2018년 9월 13일 오전 8시 17분
2021년 7월 30일 오전 4시 09분
업데이트 노트 5개 (보기)
필요한 아이템
이 항목에 필요한 다른 항목
제작자
Steve
오프라인
모음집 695개 모두 보기 (숨긴 상태 몇 개 있을 수 있습니다)
13,724 순 방문자 수
9,186 현재 구독자 수
322 현재 즐겨찾기 수

다운로드 위해 구독하기
ACE3 Compatibility for SPS AI AXMC Sniper Rifles

설명
ACE3 Compatibility for SPS AI AXMC Sniper Rifles

V1.1.0
Two new ammunition types added - Berger .338 OTM and .308 Juggernaut OTM which better ballance the performance of the 3 different calibres.

This is the ACE3 compatibility mod for the stand-alone version of SPS AI AXMC series of sniper rifles.

Some additional ACE3 ammo has been added and ACE3 ballistics should be implemented/added to all ammo and weapon types.

AtragMX presets are also included in this mod.

For full details on the Accuracy International AXMC mod, please see the following link:
https://psteamcommunity.yuanyoumao.com/sharedfiles/filedetails/?id=1510335080&tscn=1536796518
댓글 9개
< >
Steve  [작성자] 2024년 4월 5일 오후 1시 11분 
I've not updated this mod since July 2021.
Again, this is just to add ACE3 ballistics etc. to the stand along AI AXMC rifles.

It's possible something in ACE3's latest update has broken something but I don't think what you're describing is linked to this mod.
Steve  [작성자] 2024년 4월 5일 오전 11시 44분 
You mean it only happens after the latest ACE3 update?

Also, you might be posting in the wrong mod discussion - this is just the ACE3 compatibility for the stand alone SPS AI AXMC Sniper Rifle mod. You can't fit bipods or angled foregrips to that rifle.
Steve  [작성자] 2024년 4월 5일 오전 4시 08분 
Not sure what you mean by gun handle.
What I suspect is happening with laser sight (pointer/illuminator?) is that to keep the arsenal entries small, only the first function of the attachment is shown in the arsenal. You can then cycle through its other functions but if you try to save on any other than the initial one, the item will be removed.
It's either that or I start putting about 400 laser pointer options into the arsenal list...
Laid3acK 2018년 9월 16일 오전 3시 06분 
Thank you Steve. :)
Steve  [작성자] 2018년 9월 14일 오전 8시 17분 
OK - @Laid3acK - V1.0.1 should fix these issues. Most of it was being caused by the AI AXMC barrels being longer than the inherited ACE3 muzzle length arrays!
But also some additional tweaks required to ammo and AtragMX settings too so it should all line up nicely now.
Steve  [작성자] 2018년 9월 14일 오전 4시 57분 
OK - I've found at least one area where this can be caused by so will look to fix this. However, I don't think what I've found can explain all of the differences I see. (It might explain the Mk248 issues though.)
Thanks for pointing this out as it's allowing me to improve the mod further!
Steve  [작성자] 2018년 9월 14일 오전 3시 57분 
@Laid3acK- Have you tested the AtragMX settings for accuracy?
And are you refering to velocities in the config file or what you see displayed in the AtragMX's MV section?
I agree that the range card for some ammo types shows discrepency to the AtragMX settings (at standard atmospheric conditions) which I've yet to fully understand. Basically, it looks like there are some circumstances where the ACE3 fnc_updateRangeCard.sqf is not using the barrel length to calculate velocity correctly and uses 'default' settings from the magazine/ammo instead.Once I understand why this is, I will fix it.
Steve  [작성자] 2018년 9월 14일 오전 3시 57분 
My testing has shown the AtragMX presets to be pretty accurate in a range of different ambient conditions for all but the .300WinMag Mk240Mod0 and Mod1. (Which I'd still like to improve.)
So my advice for now is use the AtragMX presets not the range card.

For info, the drag coefficient and airFriction are taken exactly from ACE3. Even if these values are not quite as reality, I want to keep my mod consistent with the rest of the ACE3 setting.
Laid3acK 2018년 9월 14일 오전 2시 28분 
Hi Steve,
there is something wrong with your Muzzle Velocity Tables in your AtragMx's presets.
The AtragMx MVs must be according with the range card MVs.
Actually it's not. A quick example with the .308 M118LR :

https://steamuserimages-a.akamaihd.net/ugc/957468055303886519/E69AC7B2A5D34201B727556D0F1C0CFF798219CE/

Always take the range card MVs for your presets.

I checked the .308 rifle only but i think that you should take a look for all versions.

The Drag Coef Table and the "airFriction" should be reworked too but it's an another story. :)