STEAM-GRUPPE
Blender Source Tools BleST
Deltag i gruppe
STEAM-GRUPPE
Blender Source Tools BleST
6,804
MEDLEMMER
220
I SPIL
1,507
ONLINE
Grundlagt:
8. november 2013
Oversigt Meddelelser Diskussioner Begivenheder Medlemmer Kommentarer
Alle diskussioner > Help > Trådoplysninger
44 Colt 27. juni 2018 kl. 8:04
Axis of rotation in mdl different compared to blender
I'm making a super mario character with a spinning propeller on his head:
https://imgur.com/sAEBVzs


the propeller itself is basically centered on the character's head, and it rotates about that point in blender (rotating about the z axis).

But in the model file (imgur file above) the axis of rotation of the propeller is different (the angle is not different, just the centre of rotation).

Armature is torso bone and propeller bone, which is parented to torso bone.
propeller parented to propeller bone, everything else is parented to torso bone.
I did LocRot in blender animations.




My qc file is here:

$scale 360

$modelname "flyboy/flyboy.mdl"


$cdmaterials "models/flyboy"


$body mybody "flyboy.smd"


$sequence idle "flyboy" loop fps 1

$sequence flying "flying_001" loop fps 30

Can someone help?
Thanks.

Forfatteren af dette emne har markeret et indlæg som svaret til sit spørgsmål.
Klik her for at hoppe til det indlæg.
Oprindeligt skrevet af Zappy:
I downloaded the compiled Source model and checked it in Source Filmmaker, and yes, it seems wrong. Then I downloaded the Blender session, copied your QC file, loaded the Blender session, exported a mesh DMX (and changed the QC to load that), and compiled the model, and nothing seemed wrong.

However... You have "$scale 360" in your QC file. It's much better to do the scaling within a 3D model editor instead (so you scale it up to 360x scale in Blender and remove the $Scale line from the QC file). While I haven't tested doing so, I assume that doing that will make the model end up as you want it to, even if you do SMD exports.
< >
Viser 1-9 af 9 kommentarer
Zappy 27. juni 2018 kl. 8:36 
Please show a screenshot where the propeller bone's axis is visible in Blender, and another where it's visible in Source.
#1
44 Colt 27. juni 2018 kl. 10:42 
Bone axis in source mid animation:
https://imgur.com/AtjvDgF

Bone axis in source in idle sequence:
https://imgur.com/vAYArgT

Bone axis in blender:
https://imgur.com/gvdKY5u

I'm not sure what to make of these, the bone axis seems to be the same but the propeller mesh is clearly not rotating about the centre part.
#2
Zappy 27. juni 2018 kl. 11:20 
Does this issue also happen in Blender? And whether or not it does, please upload the Blender session and compiled Source model somewhere for us to view ourselves.
#3
44 Colt 27. juni 2018 kl. 11:35 
It doesn't happen in blender no. Here are some the drop box files, thanks.

blender file:
https://www.dropbox.com/s/vjjohtxp7s1cgne/fly_boy.blend?dl=0


compiled source file: https://www.dropbox.com/sh/h9a3l4avhuquo95/AABBO5hOvZd127yrprTpD4hXa?dl=0


Sidst redigeret af 44 Colt; 27. juni 2018 kl. 11:36
#4
Forfatteren af denne tråd har angivet, at dette indlæg besvarer det oprindelige emne.
Zappy 27. juni 2018 kl. 12:38 
I downloaded the compiled Source model and checked it in Source Filmmaker, and yes, it seems wrong. Then I downloaded the Blender session, copied your QC file, loaded the Blender session, exported a mesh DMX (and changed the QC to load that), and compiled the model, and nothing seemed wrong.

However... You have "$scale 360" in your QC file. It's much better to do the scaling within a 3D model editor instead (so you scale it up to 360x scale in Blender and remove the $Scale line from the QC file). While I haven't tested doing so, I assume that doing that will make the model end up as you want it to, even if you do SMD exports.
#5
Artfunkel 27. juni 2018 kl. 12:54 
This seems to be happening due to floating point rounding errors. These are large enough to be noticeable because you have an insane scene setup: your armature is scaled to 0.2, and then you scale the whole model by 360 in the QC file. You also have the origins of each of your meshes miles away from the geometry.

Once I brought everything within normal tolerances the problem went away.
#6
Zappy 27. juni 2018 kl. 13:03 
Oprindeligt skrevet af Artfunkel:
Once I brought everything within normal tolerances the problem went away.
Speaking of problems, when I exported a mesh DMX from that Blender session, the Blender Source Tools gave 5 or 6 warnings about there being multiple armatures... even though there only seems to be a single armature. Do you know why that is? (I do apologize for asking about an unrelated issue here, but I have never had that error myself, and I don't want to create a bug report about someone else's Blender session.)
#7
Artfunkel 27. juni 2018 kl. 13:05 
It's a bug. I've fixed it locally but it's not worth making a new release for.
#8
44 Colt 27. juni 2018 kl. 13:42 
Yes, scaling it in blender instead of the qc file fixed the issue. Thanks.
#9
< >
Viser 1-9 af 9 kommentarer
Per side: 1530 50

Alle diskussioner > Help > Trådoplysninger
Dato opslået: 27. juni 2018 kl. 8:04
Indlæg: 9
Start en ny diskussion

Diskussionsregler og retningslinjer