The last thing you broke?

所有讨论 > Steam 论坛 > Off Topic > 主题详情

Chaosolous 10 月 20 日下午 9:29

What was it and whut happund?

< >

正在显示第 1 - 15 条，共 33 条留言

craigsters 10 月 20 日下午 9:33

I took apart a 6 drawer dresser, it had a huge spider web in the bottom under it, creeped me out, needed to get it to smaller pieces to throw it out, only needed to use the hammer once, the rest I tore apart with bare hands, damn particle board cheap furniture

最后由 craigsters 编辑于; 10 月 20 日下午 9:34

Inqui999 10 月 20 日下午 9:35

A pretzel... I ate it.

swillfly 10 月 20 日下午 9:36

i broke my áss with a gaseous explosion that was a bit painful when it blew

Iratus Machina 10 月 20 日下午 9:38

A few weeks ago, broke a half-full jar of queso while I was on my way to snack on chips and queso. Slipped outta my hands and crashed onto hard floor below. Glass flew all over the floor, further than I would've expected. Took awhile to find and dispose of just about all the glass fragments, though I worry a fragment or two might still be out there. Shame I had to wait another day or two to snack on queso goodness, but ♥♥♥♥ happens.

最后由 Iratus Machina 编辑于; 10 月 20 日下午 9:41

Mina 10 月 20 日下午 9:39

phone drop

libadwaita ΘΔ (she/they) 10 月 20 日下午 9:40

probably a ceramic bowl that slipped out of my hand while I was washing it

最后由 libadwaita ΘΔ (she/they) 编辑于; 10 月 20 日下午 9:40

Goldias 10 月 20 日下午 9:48

Enemy line of sight.
To cancel alert phase.

Abaddon the Despoiler 10 月 21 日上午 12:27

My nicotine, weed and alcohol addictions.

Sixtyfivekills 10 月 21 日上午 12:28

引用自 Abaddon the Despoiler：
My nicotine, weed and alcohol addictions.

Pro gamer!

Dutchgamer1982 10 月 21 日上午 12:41

my washing machine handle...

tried opening my washing machine.. while it was locked... thus breaking off the handle..
thought machine was ready.. apearingly it was not.. it just had leaked
(rubber strip was not properly in place so water leaked out during washing)
as my washing machine is in my bathroom.. and it ran during night.. the floor was already dry by the time I arrived

apearingly it detects if it has not enough water mid-program than tries to pump in more.. if that fails to raise the level to sufficient.. it presumes it has no water acces.. and shuts itself off..
but when it does that.. it does NOT unlock the door

#10

TheStoryteller01 10 月 21 日上午 1:03

Another poster.

#11

Magic A. I. 10 月 21 日上午 1:50

I broke radio silence after breakfast which caused a record-breaking heart-break. And then this subversion happened: C-C-C-COMBO BREAKER!!!

#12

Painkilleruk 23 小时以前

引用自 Magic A. I.：
I broke radio silence after breakfast which caused a record-breaking heart-break. And then this subversion happened: C-C-C-COMBO BREAKER!!!

epic killer instinct reference

3d printer, long story short I am done with creality products - my k2 was on a 24hr print and messed it up on the 24hr so i thought i would treat it to a flying lesson out the window.

#13